Troubleshooting - Steinbach Speedcleaner RX 5 Manual De Instrucciones

Trouble shooting
Fault Cause
Cable was not relea-
sed properly
The power
cable is The cable in the water
twisted or is too long.
tangled.
Cleaner is stuck on
the outlet grille
The power unit is in
the wrong place.
Water circulation in the
pool is switched on.
The cleaner
Connection cable is
cannot reach
too short.
all areas.
Filter bag is blocked.
Algae is growing on
the walls.
Water temperature is
too high / too low.
Cleaner does
not climb up
Brushes are worn
the pool wall.
The cleaner is too
light, it is tilting.
PH value is not
correct.
Power pack is not fully
plugged in.
The cleaner was
Cleaner is damaged during trans-
not operating. port.
The operating unit
needs a different vol-
tage to the local one.
Cleaner does There is air in the
not sink. cleaner.
Drive roller Foreign body in the
breaks off. drive.
Cleaner Cleaner climbs too
comes up high, air in the cleaner
Cleaner is Faulty operation.
faulty.
Important Note
Technical data
■ Input voltage: 220(230) VAC
■ Frequency:: 50 Hz
■ Output voltage: DC (direct current) 24 V
■ Rated power: 200 W
■ Cable length: 18 m
■ Width of cleaning drum: 358 mm
■ max. Cleaning area in swimming pool: 200 m²
■ Filter performance: 15m³/h
■ Filter grade: 200 μm
■ Operating temperature (water): 10°C - 32°C
10
Solutionn
Switch off the unit, release
and uncoil the cable.
Remove the excess cable
from the water.
Switch off the filter unit.
Position the power unit so
that the cleaner can reach
all areas properly.
Switch off the filter unit.
Place the greatest possible
length of connecting cable
into the pool, but bear in
mind the corresponding
minimum distance between
the operating unit and the
pool.
Replace the filter bag.
Clean the pool walls.
Optimal water temperature
is between 10°C and 32°C.
Contact a dealer, replace
the brushes.
Switch the unit off and allow
the air to escape.
Test the value to keep it
between 7.0 and 7.4.
Check the power cable and
the operating unit.
Contact a specialist retailer.
Contact a specialist retailer.
Switch the unit off, allow the
air to escape, and let the
cleaner sink to the bottom.
Contact a specialist retailer.
Switch the unit off, allow the
air to escape.
Contact your retailer.
■ Crawl speed: 12m/min
■ Hydrolytic resistance class: Cleaner: IPX8; Electricity control box/
power supply: IPX5
■ Surrounding temperature: 10°C - 40°C
■ Weight of the cleaner: 9,5 kg (without cable)
Service
Please do not send the equipment to us without authorisation, but
please contact our service centre initially!
If the equipment has to be collected, it must be packed securely and
the invoice (copy) must the enclosed.
As soon as the unit reaches us, it will be checked for faults by our
claims department, and repaired. On conclusion of this work, your
equipment will be returned to you as quickly as possible.
If this return is not covered by the guarantee, the costs incurred will
be calculated.
Guarantee processing / guarantees are handled by the company
Steinbach VertriebsgmbH.
The item will be repaired by the company Steinbach VertriebsgmbH,
however where no right of return exists it will not be taken back.
Cleaning
Use conventional cleaning products. Do not use solvent-based or abra-
sive cleaning agents/tools, i.e. no hard sponges, brushes etc..
Storage
The product must be thoroughly dried after cleaning. After which, it is to
be stored in a dry location protected from frost.
Disposal
Disposing of packaging: The packaging material has been selected
in view of environmental concerns and disposability and is therefore
recyclable. The paper and cardboard can be recycled, as can the plastic
coverings.
Disposing of the product: Applicable in the European Union and other
European states with systems in place for collecting and sorting recycla-
ble materials. Dispose of the product in accordance with any laws and
regulations applicable at your place of residence.
Warranty conditions
The respective country's legal provisions for warranty conditions shall
apply accordingly. For Austria and Germany, these apply for 2 years
after the date of invoice.
Declaration of conformity (CE)
The EU declaration of conformity can be requested via the address
shown at the end of this manual.
Symbol explanation
CE: Declaration of Conformity (see "Declaration of Conformity" chapter):
This symbol designates products which fulfil all applicable community
regulations of the European Economic Area.
EN
061018_v1801