Makita BTD144 Manual De Instrucciones página 7

Atornillador de impacto inalámbrico
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 30
OPERATION
The proper fastening torque may differ depending upon
the kind or size of the screw/bolt, the material of the
workpiece to be fastened, etc. The relation between fas-
tening torque and fastening time is shown in the figures.
(Fig. 12, 13 & 14)
Hold the tool firmly and place the point of the driver bit in
the screw head. Apply forward pressure to the tool to the
extent that the bit will not slip off the screw and turn the
tool on to start operation.
NOTE:
• Use the proper bit for the head of the screw/bolt that
you wish to use.
• When fastening screw M8 or smaller, choose a proper
hammer force, and carefully adjust pressure on the
switch trigger so that the screw is not damaged.
• Hold the tool pointed straight at the screw.
• If the hammering force is too strong you tighten the
screw for a time longer than shown in the figures, the
screw or the point of the driver bit may be overstressed,
stripped, damaged, etc. Before starting your job,
always perform a test operation to determine the
proper fastening time for your screw.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspec-
tion or maintenance except for the following troubleshooting related to the light.
Troubleshooting
Trouble
Flickers twice per second.
Flickers three times per second.
(LED indicator for empty signal for
remaining battery capacity also flickers.)
The tool stops
Flickers five times per second.
during operation.
Flickers once per second.
Not flickers.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
Light status
The fastening torque is affected by a wide variety of fac-
tors including the following. After fastening, always check
the torque with a torque wrench.
1.
When the battery cartridge is discharged almost
completely, voltage will drop and the fastening
torque will be reduced.
2.
Driver bit or socket bit
Failure to use the correct size driver bit or socket bit
will cause a reduction in the fastening torque.
3.
Bolt
• Even though the torque coefficient and the class of
bolt are the same, the proper fastening torque will
differ according to the diameter of bolt.
• Even though the diameters of bolts are the same,
the proper fastening torque will differ according to
the torque coefficient, the class of bolt and the bolt
length.
4.
The manner of holding the tool or the material of
driving position to be fastened will affect the torque.
5.
Operating the tool at low speed will cause a reduc-
tion in the fastening torque.
Steps to be taken
The tool temperature is high. Cool down it fully.
The tool restarts after its temperature becomes low.
Remaining battery capacity level is low. Charge the
battery cartridge. When the LED indicator still flickers
even after charging the battery cartridge, stop using
and have the tool repaired by a Makita local service
center.
Use the tool with the motor not locked. If the motor
remains locked, stop using and have the tool repaired
by a Makita local service center.
Stop using and have the tool repaired by a Makita
local service center.
The tool stops when continuing to pull the switch
trigger for more than approximately 2 minutes.
Release the switch trigger.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Screw bits
• Hook
• Plastic carrying case
• Various type of Makita genuine batteries and chargers
7
Tabla de contenido
loading

Tabla de contenido