Cleaning Drain Using 5 / 8 Sectional Cable; Description, Specifications And Standard Equipment; Description; Specifications - RIDGID K-50 Manual De Uso

Description, Specifications and

Standard Equipment

Description

The RIDGID K-50 is a portable Drain Cleaning Machine
designed to clean 1
clude sink, shower and floor drains. Capable of running
three different size cables:
The machine is driven by a 1/6 HP motor that has a
grounded electrical system. An integral Ground Fault In -
terrupter (GFCI) is built into the line cord. A toggle switch
provides FORWARD/OFF/REVERSE control of the motor.
The K-50 is designed to use
cable that has a quick change coupling system for dis-
connecting tools. The cable is manually fed in and out of
the drain and rotates at a speed of 400 RPM. The rotation
of the cable is controlled by a clutch handle. The cable
stops instantly when the clutch handle is released.
The K-50 is also designed to use with the A-17 Adapters.
Adapters will hold
Rotation of the adapters is controlled by the clutch handle.
The cable adapter is equipped with a quick-acting brake
which immediately stops rotation of the drum when the
clutch handle is pulled upward.

Specifications

Line Capacity ...............Depends on choice of cable.
Recommended Line Size and Reach
Cable Size
5 / " Cable
16
3 / " Cable
8
5 / " (C-8)
8
5 / " (C-9)
8
Cable Sizes ..................
Motor
Type ..............................115V/50-60 Hz, Reversible,
Rating ............................
Amps .............................4
Weight...........................37.5 lbs. (17 kgs.)
Dimensions
Length ...........................12" (305mm)
Height ............................17.5" (445mm)
Width .............................13" (330mm)
278-104-431.10_REV. C
Find Quality Products Online at:
1 / " to 4" drain "lines. Ap pli cations in-
4
5 / ", 3 / " and 5 / ".
16 8 8
5 / - diameter sectional-type
8
5 / " or 3 / " continuous length cables.
16 8
Refer to the following chart
for recommendations.
Line Size Reach
3 / " - 1" 25' - 50'
4
1 1 / " - 2" 25' - 35'
4
1 1 / " - 3" 100'
4
2" - 4" 100'
5 / ", 3 / " and 5 / "
16 8 8
230V Available Upon Request
1 / HP
6
GlobalTestSupply
www.
K-50 Drain Cleaning Machine
Sound Pressure (L )* ......69.2 dB(A), K=3
PA
Sound Power (L )*...........74.5 dB(A), K=3
WA
* Sound measurements are measured in accordance with a standardized test per
Standard EN 62841-1.
- Sound emissions may vary due to your location and specific use of these tools.
- Daily exposure levels for sound need to be evaluated for each application and
appropriate safety measures taken when needed. Evaluation of exposure lev-
els should consider the time a tool is switched off and not in use. This may sig-
nificantly reduce the exposure level over the total working period.
Standard Equipment
Catalog No. Model
No. Description
115V 230V
58920 76455 K-50 Machine Only
58960 76475 K-50-4 Machine with:
– A-30 Cable Kit
58980 76485 K-50-6 Machine with:
– A-17-A Adapter
– A-30 Cable Kit
59000 76495 K-50-8 Machine with:
– A-17-A Adapter
– A-18-B Adapter
– A-30 Cable Kit
52972 — K-50-9 Machine with:
– A-40 Cable Kit
Model
No. Cable Tools & Accessories
A-30 Six Sections: T-201 Straight Auger
C-8, 5 / " x 7 1 / ' T-202 Bulb Auger
8 2
(45', 13.7m) T-205 "C" Cutter
T-211 Spade Cutter
A-13 Coupling Pin Key
A-10 Cable Carrier
A-14-6 Rear Guide Hose
A-1 Left-Hand Mitt
A-40 Six Sections: T-206 Funnel Auger
/ " x 10' T-215 4-Blade Cutter
C-9, 5
8
(60' , 18.3m) T-231 "C" Cutter
A-13 Coupling Pin Key
A-10 Cable Carrier
A-14-610 Rear Guide Hose
A-1 Left-Hand Mitt
Model
No. Description
A-17-A Adapter with 25' x 5 /
A-17-B Adapter with 35' x 3 /

Machine Inspection

WARNING
To prevent serious injury, inspect your Drain
Cleaning Machine. The following inspection pro-
cedures should be performed before each use.
.com
[email protected]
" Cable w/Bulb Auger
16
" Cable w/Bulb Auger
8
5