Drill Safety Warnings; Standard Accessories; Prior To Operation - Hitachi Koki D 10VC2 Instrucciones De Manejo

DRILL SAFETY WARNINGS

1. Wear ear protectors with impact drills.
Exposure to noise can cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Hold the drill securely when using.
SPECIFICATIONS
Voltage (by areas)*
Power input
No load speed
Drill chuck capacity
Steel Twist Bit
Flat Spade Bit
Capacity
Wood
Auger Bit
Weight (without cord)
* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

○ Chuck wrench (Spec. only for keyed chuck) .................1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
(1) Side handle
(2) Hook
(3) Hook (A)
Optional accessories are subject to change without notice.
APPLICATIONS
○ Boring holes in metal, wood and plastic.

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If the
plug is connected to a receptacle while the power switch
is in the ON position, the power tool will start operating
immediately, inviting serious accident.
3. Extension cord
When the work area is removed from the power source.
Use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Selecting the appropriate drill bit
○ When boring metal or plastic
Use ordinary metalworking drill bits.
○ When boring wood
Use ordinary woodworking drill bits.
However, when drilling 6.5 mm or smaller holes, use a
metalworking drill bit.
5. Mounting and dismounting of the bit
For keyed chuck (Fig. 1)
(1) Open the chuck jaws, and insert the bit into the chuck.
4. Do not wear gloves made of stuff liable to roll up such as
cotton, wool, cloth or string, etc.
5. Prior to drilling into walls, ceilings or fl oors, ensure there
are no electric cables or conduits inside.
(110 V, 115 V, 120 V, 127 V, 220 V, 230 V, 240 V)
460 W*
0 – 2300/min
10 mm
10 mm
25 mm
16 mm
1.3 kg
(2) Place the chuck wrench in each of the three holes in the
chuck, and turn it in the clockwise direction (viewed from
the front side). Tighten securely.
(3) To remove the bit, place the chuck wrench into one of
the holes in the chuck and turn it in the counterclockwise
direction.
For keyless chuck
(1) Open the chuck jaws, and insert the bit into the chuck.
To open the chuck jaws, hold the ring while turning the
sleeve in the counterclockwise direction (viewed from the
front side).
(2) Firmly grasp the ring and turn the sleeve in the clockwise
direction. Tighten securely.
(3) To remove the bit, fi rmly grasp the ring and turn the
sleeve in the counterclockwise direction.
(4) If it is hard to loosen the sleeve, fi x the spindle
using the open-end
fi rmly, and turn
(counterclockwise
(Fig. 3)
6. Check the rotational direction (Fig. 4)
The bit rotates clockwise (viewed from the rear side) by
pushing the R-side of the push button.
The L-side of the push button is pushed to turn the bit
counterclockwise.
(The and
R
L
7. Installing the side handle (Optional accessory)
A Side handle can be installed on either side of the tool
for right or left handed use.
To install the side handle, thread it into the socket on the
desired side of the gear cover and tighten it securely.
(Fig. 6)
8. Attaching the hook (Optional accessory)
For hook (side-attaching)
Fix the hook fi rmly on the desired side of the gear cover
using M10 bolt which is supplied with hook.
For hook (A) (top-attaching)
To attach the hook (A), it is necessary to disassemble the
handle portion which covered the tool's electrical system.
English
(Fig. 2)
wrench, hold
it in the loosening
when viewed from
marks are provided on the body.)
(Fig. 7)
(Fig. 8)
the sleeve
direction
the front).
4