HERKULES K 1500 UV Manual De Instrucciones página 18

Anleitung TK 1500 SPK7 18.08.2006
GB
When working outdoors, use only extension
cables that are approved for outdoor use and
which are marked accordingly.
Concentrate on what you are doing. Use
common sense. Do not operate the tool if your
mind is not on your work.
Never use an electric tool with a switch that
cannot be turned on and off.
Warning! The use of plug-in tools and
accessories other than those intended may put
you at risk of injury.
Always pull the plug out of the power socket
before adjusting or servicing the machine.
Give these safety regulations to all persons who
work on the machine.
Do not use this saw to cut fire wood.
Do not use this saw to cross-cut roundwood.
Caution! Hands and fingers may be injured on
the rotating saw blade.
The machine is equipped with a safety circuit-
breaker (11) to prevent it starting up again after
a voltage drop.
Before you use the machine for the first time,
check that the voltage marked on the rating plate
is the same as your mains voltage.
If you need to use an extension cable, make
sure its conductor cross-section is big enough
for the saw's power consumption. Minimum
cross-section: 1,5 mm 2 .
If you use a cable reel, the complete cable has
to be pulled off the reel.
Do not carry the tool by its cable.
Check the power cable. Never use a faulty or
damaged power cable.
Do not use the cable to pull the plug out of the
socket. Protect the cable from heat, oil and
sharp edges.
Do not leave the saw in the rain and never use it
in damp or wet conditions.
Provide good lighting.
Do not saw near flammable liquids or gases.
Wear suitable work clothes! Loose garments or
jewelry may become caught up in the rotating
saw blade.
Non-slip shoes are recommended when working
outdoors.
Wear a hair net if you have long hair.
Avoid abnormal working postures.
Operators have to be at least 18 years of age.
Trainees of at least 16 years of age are allowed
to use the machine under supervision.
Keep children away from the machine when it is
connected to the power supply.
Keep your workplace clean of wood scrap and
any unnecessary objects.
An untidy work area invites accidents.
18
12:18 Uhr Seite 18
Do not allow other persons, especially children,
to touch the tool or cable. Keep them out of your
work area.
Persons working on the machine should not be
distracted.
Note the direction of rotation of the motor and
saw blade. Use only blades whose permissible
maximum speed is not lower than the maximum
spindle speed of the bench-type circular saw
and of the material to be cut.
After you have switched off the motor, never
slow down the saw blade (4) by applying
pressure to its side.
Fit only blades (4) which are well sharpened and
have no cracks or deformations.
Use only circular saw blades (4) made of high-
alloy high-speed steel (HSS).
Use only blades which are recommended by the
manufacturer, comply with EN 847-1 and come
with a warning notice. When changing the blade,
make sure that the cutting width is not smaller
and the saw plate not bigger than the thickness
of the splitter.
Faulty saw blades (4) have to be replaced
immediately.
Never use saw blades which do not comply with
the data specified in this manual.
Never wedge the hinged guard hood (2) in open
position. Use the upper blade guard and set it to
the correct position.
Never dismantle the machine's safety devices
(2, 5) or put them out of operation.
If the table insert is worn, replace it.
Use the splitter correctly and set it to the correct
position. The splitter (5) is an important safety
device. Not only does it guide the workpiece, it
also prevents the kerf closing behind the blade
so that there is no kickback from the workpiece.
Note the thickness of the splitter.
The guard hood (2) has to be lowered over the
workpiece for each cut.
Be sure to use a push stick (3) when slitting
narrow workpieces (smaller than 120 mm in
width). Keep the push stick or handle for a push
block at the machine at all times, even when you
are not using them.
Never cut workpieces which are too small to hold
securely in your hand.
Important: It is prohibited to use this saw to
make plunge cuts.
Always stand to the side of the saw blade when
working with the saw.
Never load the machine so much that it cuts out.
Always press the workpiece firmly against the
saw table (1).
Make sure that off-cuts do not catch on the saw