Tabla de contenido
Idiomas disponibles
Idiomas disponibles
3. 240 VOLT SINgLE PHASE OPERATION
The motor supplied with your machine is a dual
voltage, 120/240 volt motor. It is shipped ready-
to-run for 120 volt operation. However, it can be
converted for 240 volt operation.
A qualified electrician should do the conversion, or
the machine can be taken to an Authorized DELTA
Service Center. When completed, the machine must
conform to the National Electric Code and all local
codes and ordinances.
The machine is typically converted by re-wiring the
motor for 240 volts, installing a 240 volt plug on the
power supply cord and replacing the switch with one
that is rated for 240 volt operation.
Be sure the 240 volt plug is only used in an outlet
having the same configuration as the plug illustrated
in Fig. C. No adapter should be used with the 240
volt plug.
ExTENSION CORdS
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension
cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine's plug. When using
an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a
drop in line voltage, resulting in loss of power and overheating. Fig. D-1 or D-2, shows the correct gauge to use depending
on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
MINIMUM gAUgE ExTENSION CORd
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Total Length
Rating
Volts
of Cord in Feet
0-6
120
up to 25
0-6
120
25-50
0-6
120
50-100
0-6
120
100-150
6-10
120
up to 25
6-10
120
25-50
6-10
120
50-100
6-10
120
100-150
10-12
120
up to 25
10-12
120
25-50
10-12
120
50-100
10-12
120
100-150
12-16
120
up to 25
12-16
120
25-50
12-16
120
GREATER THAN 50 FEET NOT RECOMMENDED
Fig. d-1
FOREWORd
The 50-850 Dust Collector will connect to woodworking machines that accept a 4" (101.6 mm) diameter hose. The
50-850 comes with a five micron filter bag, one six mil plastic collection bag and a 4" x 5' (101.6 mm x 1524 mm)
collection hose.
NOTICE: The manual cover illustrates the current production model. All other illustrations contained in the manual are
representative only and may not depict the actual labeling or accessories included. These are intended to illustrate
technique only.
gauge of
Extension Cord
18 AWg
16 AWg
16 AWg
14 AWg
18 AWg
16 AWg
14 AWg
12 AWg
16 AWg
16 AWg
14 AWg
12 AWg
14 AWg
12 AWg
FUNCTIONAL dESCRIPTION
6 -
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
SHOCK HAzARd. In all cases, make
certain that the receptacle in question is properly
grounded. If you are not sure, have a qualified
electrician check the receptacle.
MINIMUM gAUgE ExTENSION CORd
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating
Volts
0-6
240
0-6
240
0-6
240
0-6
240
6-10
240
6-10
240
6-10
240
6-10
240
10-12
240
10-12
240
10-12
240
10-12
240
12-16
240
12-16
240
12-16
240
English
Fig. C
Total Length
gauge of
of Cord in Feet
Extension Cord
up to 50
18 AWg
50-100
16 AWg
100-200
16 AWg
200-300
14 AWg
up to 50
18 AWg
50-100
16 AWg
100-200
14 AWg
200-300
12 AWg
up to 50
16 AWg
50-100
16 AWg
100-200
14 AWg
200-300
12 AWg
up to 50
14 AWg
50-100
12 AWg
GREATER THAN 100 FEET NOT RECOMMENDED
Fig. d-2
Tabla de contenido
