Noise Information - Milwaukee M18 FMS190 Manual Original

Technical Data
Mitresaw
Production code
No-load speed
Battery voltage
Saw blade dia. x hole dia
Saw blade body thickness max.
Saw blade tooth thickness min.
Cutting widthmax.
Mitre 0°/ Bevel 0°
Mitre 45°/ Bevel 0°
Mitre 0°/ Bevel L45°
Mitre 0°/ Bevel R45°
Mitre L45°/ Bevel L45°
Mitre L45°/ Bevel R45°
Mitre R45°/ Bevel L45°
Mitre R45°/ Bevel R45°
Max. Cutting depth at
Mitre 0°/ Bevel 0°
Mitre L45°/ Bevel 0°
Mitre R45°/ Bevel 0°
Weight according EPTA-Procedure 01/2003
Permitted Ambient Temperature
during charging
during operation and during storage
Recommended battery packs
Recommended charger

Noise information

Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
WARNING Read all safety warnings, instructions,
illustrations and speci cations provided with this power tool.
Failure to follow the warnings and instructions may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference.
MITRE SAW SAFETY WARNINGS
a) Mitre saws are intended to cut wood or wood-like
products, they cannot be used with abrasive cut-o wheels
for cutting ferrous material such as bars, rods, studs, etc.
Abrasive dust causes moving parts such as the lower guard to jam.
Sparks from abrasive cutting will burn the lower guard, the kerf
insert and other plastic parts.
b) Use clamps to support the workpiece whenever possible.
If supporting the workpiece by hand, you must always
keep your hand at least 100 mm from either side of the saw
blade. Do not use this saw to cut pieces that are too small
to be securely clamped or held by hand. If your hand is placed
too close to the saw blade, there is an increased risk of injury from
blade contact.
c) The workpiece must be stationary and clamped or held
against both the fence and the table. Do not feed the
workpiece into the blade or cut "freehand" in any way.
Unrestrained or moving workpieces could be thrown at high
speeds, causing injury.
d) Push the saw through the workpiece. Do not pull the
saw through the workpiece. To make a cut, raise the saw
head and pull it out over the workpiece without cutting,
start the motor, press the saw head down and push the saw
through the workpiece. Cutting on the pull stroke is likely to
cause the saw blade to climb on top of the workpiece and violently
throw the blade assembly towards the operator.
e) Never cross your hand over the intended line of cutting
either in front or behind the saw blade. Supporting the
workpiece "cross handed" i.e. holding the workpiece to the right of
the saw blade with your left hand or vice versa is very dangerous.
f) Do not reach behind the fence with either hand closer
than 100 mm from either side of the saw blade, to remove
wood scraps, or for any other reason while the blade is
spinning. The proximity of the spinning saw blade to your hand
may not be obvious and you may be seriously injured.
M18 FMS190
4606 35 01...
...000001 - 999999
5000 min
-1
18 V
190 x 30 mm
3,0 mm
1,6 mm
55,4 mm x 215,5 mm
55,4 mm x 152,7 mm
39,3 mm x 215,5 mm
19,5 mm x 215,5 mm
39,3 mm x 152,7 mm
19,5 mm x 152,7 mm
39,3 mm x 152,7 mm
19,5 mm x 152,7 mm
90,9 mm x 21,8 mm
90,9 mm x 20,3 mm
GB
90,9 mm x 17,8 mm
12,7 kg (5,0 Ah)
0 - 50 °C
-18 - 50 °C
M18 B...
M12-18 C
M12-18 FC
M12-18 AC
88,9 db(A)
99,9 db (A)
English
23