Additional Safety Rules - Makita 2414NB Manual De Instrucciones

ENGLISH
1 Safety guide
2 Shaft lock
3 Socket wrench
4 Cut-off wheel
5 Inner flange
6 O-ring
7 Spindle
8 Ring
9 Outer flange
10 Hex bolt
11 Screw
12 Spark guard
SPECIFICATIONS
Model
Wheel diameter .................................................................................................................................................. 355 mm
Hole diameter .................................................................................................................................................... 25.4 mm
–1
No load speed (min ) ............................................................................................................................................ 3,800
Dimensions (L x W x H)
With under cover..............................................................................................................500 mm x 280 mm x 620 mm
Without under cover.........................................................................................................500 mm x 280 mm x 600 mm
Net weight
For tools with European type safety guide and under cover.............................................................................. 18.5 kg
For tools with European type safety guide and without under cover ................................................................. 17.8 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for cutting in masonry and ferrous
materials with appropriate abrasive cut-off wheel.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Wear protective glasses. Also wear hearing pro-
tection during extended periods of operation.
2. Use only wheels recommended by the manufac-
turer which have a maximum operating speed at
least as high as "No Load RPM" marked on the
tool's nameplate. Use only fiberglass-reinforced
cut-off wheels.
3. Check the wheel carefully for cracks or damage
before operation. Replace cracked or damaged
wheel immediately.
4.
Secure the wheel carefully.
5. Use only flanges specified for this tool.
6. Be careful not to damage the spindle, flanges
(especially the installing surface) or bolt, or the
wheel itself might break.
Explanation of general view
13 Stopper plate
14 Guide plate
15 Hex bolts
16 Vise plate
17 Vise nut
18 Vise handle
19 Spacer block
20 Straight piece of wood
(Spacer) vm
21 Over 190 mm long
22 Over 45 mm wide
23 Over 65 mm wide
7.
8.
9.
10. Make sure the wheel is not contacting the work-
11. Before using the tool on an actual workpiece, let
12. Watch out for flying sparks when operating.
13. Remove material or debris from the area that
14. Use the cutting edge of the wheel only. Never
15. If the wheel stops during the operation, makes
ENB066-1
16. Always switch off and wait for the wheel to come
17. Do not touch the workpiece immediately after
18. Store wheels in a dry location only.
SAVE THESE INSTRUCTIONS.
24 Diameter of workpiece
25 Spacer block
26 Vise
27 Width of spacer block
28 Blocks
29 Switch trigger
30 Lock button/Lock-off button
31 Wing bolt
32 Under cover
33 Limit mark
34 Screwdriver
35 Brush holder cap
Keep guards in place and in working order.
Hold the handle firmly.
Keep hands away from rotating parts.
piece before the switch is turned on.
it simply run for several minutes first. Watch for
flutter or excessive vibration that might be
caused by poor installation or a poorly balanced
wheel.
They can cause injury or ignite combustible
materials.
might be ignited by sparks. Be sure that others
are not in the path of the sparks. Keep a proper,
charged fire extinguisher closely available.
use side surface.
an odd noise or begins to vibrate, switch off the
tool immediately.
to a complete stop before removing, securing
workpiece, working vise, changing work posi-
tion, angle or the wheel itself.
operation; it is extremely hot and could burn
your skin.
2414NB
5