Colour Surface; Interconnecting Several Rgbl-82Dmx; Remote Control With The Lc-3 - IMG STAGELINE RGBL-82DMX Manual De Instrucciones

low. Confirm the adjustment with button ENTER.
The display stops flashing and returns to the indi-
cation of the programme number after 8 seconds.
If the music is played with a clear rhythm in the bass
range at sufficient volume, the selected programme is
controlled via the internal microphone. With each
music control pulse the green LED SOUND (14)
shortly lights up. If the music control should not oper-
ate in an optimum way, increase the volume or reduce
the distance between sound source and light effect
panel.

6.1.2 Colour surface

The unit is capable of radiating one of 9 preset colours
at maximum brightness or a manually adjusted colour
at any desired brightness.
A Selecting a preset colour
1) Press button MENU (11) so many times until
is displayed.
2) Activate the menu item with button ENTER (13).
The display shows the colour last adjusted (
oder ) in a flashing way.
3) Select a colour with button DOWN or UP (12)
[1 = white ... 9 = blue,
ment, next paragraph] and confirm with button
ENTER. The display stops blinking.
B Manual colour adjustment
Hint: When adjusting the brightness of the red, green, or
blue LEDs, not only their brightness will be modified but in
case of a combination of these colours, also the shade of
colour will be modified. Therefore, first adjust the colour
which is intended to dominate to the desired brightness, and
then add the other two colours. For the combination white,
first adjust the brightness of the colour green because this
colour appears to the eye to be the brightest colour. Then add
red to result in yellow and finally add blue to result in white.
1) Press button MENU (11) so many times until the
display shows .
2) Activate the menu item with button ENTER (13).
The display shows the colour last adjusted (
oder ) in a flashing way.
3) Use button DOWN or UP (12) to switch to
(manual). Activate the function with button ENTER.
The display now shows
for the red LEDs.
4) Use button ENTER to switch to for the colour green
and to for blue and then back again to for red.
5) Adjust the selected colour with button DOWN or UP
(indication 0 – 255) so that the desired shade of
colour with the desired brightness will result.
6) For fine adjustment of the shade of colour, a colour
can be selected again with button ENTER and be
readjusted with the buttons DOWN and UP.
7) If no button is actuated within 8 seconds, the dis-
play returns to the indication
shade of colour, start again with operating step 1, if
required.
...
= manual colour adjust-
...
and the brightness value
. To change the
6.2 Interconnecting several RGBL-82DMX units
Several RGBL-82DMX units may be interconnected.
Then all slave units can be controlled in sync with the
master unit.
1) Connect the DMX OUTPUT (7) of the master unit
via a 3-pole XLR cable (e. g. series MEC-... or
MECN-... from the product range of "img Stage
Line") to the DMX INPUT (8) of the first slave unit.
2) Connect the DMX OUTPUT of the first slave unit to
the DMX INPUT of the second slave unit, etc. until
all units have been connected in a chain.
No DMX signal must be present at the DMX INPUT of
the master unit, so that the yellow LED MASTER (10)
lights up and the unit is thus switched to the master
mode. Once the control signals from the master unit
are applied to the slave units, the red LED SLAVE (15)
will light up on the slave units. The slave units are then
automatically switched to the slave mode and can be
controlled in sync with the master unit.

6.3 Remote control with the LC-3

The remote control LC-3 available as an accessory
allows to control various functions. There must be no
DMX signal at the DMX INPUT (8).
1) Connect the remote control to the jack REMOTE
CTRL ONLY (6).
2) Via the DMX OUTPUT (7), further RGBL-82DMX
units may be connected (
control them together with the master unit via the
remote control.
3) With button STAND BY (17), the LEDs of the light
effect panel can be switched on or off. When the
LEDs are switched off, the LED next to button
STAND BY will light up as a check.
4) Use button MODE (19) to select the desired function:
Programme No. 0 (
– The LED of button MODE does not light up –
By keeping button FUNCTION (18) pressed one
of the four stroboscope functions may be acti-
vated:
1. Permanent stroboscope with white light
2. Permanent stroboscope with coloured light
3. Stroboscope with white light, music-controlled
4. Stroboscope with coloured light, music-con-
trolled
When keeping button FUNCTION pressed
again, the next stroboscope function is adjusted
in each case.
Colour surface
– The LED of button MODE lights up perma-
nently –
Use button FUNCTION to select one of the nine
preset colours and a colour manually adjusted at
the light effect panel (indication
ter 6.1.2, section B).
chapter 6.2) in order to
chapter 6.1.1)
,
GB
chap-
15