Explanation Of General View; General Power Tool Safety Warnings; Planer Safety Warnings; Functional Description - Makita 1911B Manual De Instrucciones

ENGLISH
(Original instructions)
1 Knob
2 Switch trigger
3 Lock button/Lock-off button
4 Socket wrench
5 Installation bolt
6 Bolt
7 Drum
8 Planer blade
9 Drum cover
10 Adjust plate
11 Screws
SPECIFICATIONS
Model
Planing width ...................................................... 110 mm
Planing depth ......................................................... 2 mm
–1
No load speed (min ) .......................................... 16,000
Overall length ..................................................... 355 mm
Net weight ............................................................. 4.3 kg
Safety class ..............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for planing wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

PLANER SAFETY WARNINGS

1. Wait for the cutter to stop before setting the tool
down. An exposed cutter may engage the surface
leading to possible loss of control and serious injury.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
3. Rags, cloth, cord, string and the like should
never be left around the work area.
4. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
4

Explanation of general view

12 Heel of adjust plate
13 Back side of gauge base
14 Blade edge
15 Planer blade
16 Inside edge of gauge plate
17 Gauge plate
18 Screwdriver
19 Nozzle assembly
20 Vacuum cleaner
21 Start
22 End
5.
1911B
6.
7.
8.
9.
/II
10. Make sure the blade is not contacting the work-
11. Wait until the blade attains full speed before cut-
12. Always switch off and wait for the blades to
13. Never stick your finger into the chip chute.
14. Do not leave the tool running. Operate the tool
15. Always change both blades or covers on the
16. Use only Makita blades specified in this manual.
GEA010-1
17. Always use the correct dust mask/respirator for
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product.
GEB010-3
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Adjusting the depth of cut (Fig. 1)
Depth of cut may be adjusted by simply turning the knob
on the front of the tool.
23 Align the "V" groove with the
edge of the workpiece.
24 Sharpening holder
25 Wing nut
26 Blade (A)
27 Blade (B)
28 Side (C)
29 Side (D)
Use only sharp blades. Handle the blades very
carefully.
Be sure the blade installation bolts are securely
tightened before operation.
Hold the tool firmly with both hands.
Keep hands away from rotating parts.
Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly
balanced blade.
piece before the switch is turned on.
ting.
come to a complete stop before any adjusting.
Chute may jam when cutting damp wood. Clean
out chips with a stick.
only when hand-held.
drum, otherwise the resulting imbalance will
cause vibration and shorten tool life.
the material and application you are working
with.