GE GeoSpring GEH50DEED Serie Manual Del Propietario E Instalación página 20

Troubleshooting...
Water is too hot
Possible Causes What To Do
Water temperature is set • See About the W(]ter Temper(]ture Setting section.
too high.
A CAUTION: For your s(]fety, 0O NOT
(]ttempt rep(]ir
ofelectric(]l
wiring, controls,
he(]ting elements or other s(]fety devices. Refer rep(]irs to qu(]lified service personnel.
Electronic control has foiled. • Coil for service.
Rumbling noise Water conditions in your • Remove (]nd cleon the he(]ting elements. This should only
home caused o buildup of be done by (] qulified service personnel.
scale or mineral deposits
on the heating elements.
Relief valve producing Pressure buildup caused • This is on un(]ccept(]ble condition (]nd must be corrected.
popping sound by thermal expansion Cont(]ct the w(]ter supplier or plumbing contr(]ctor on how
or draining to o closed system, to correct this. Do not plug the relief v(]lve outlet.
The heater is beeping
and the display says
F]]
The water heater has not
been filled with water before
powering up. Powering up the
heater without water will
damage the electric heaters.
The water heater warranty
does not cover damage or
failure resulting from operation
with on empty or partially
empty tank.
The filter light is on. The filter requires cleaning.
A cleon filter is necessary for
effective operation.
The heater is beeping There is on issue with the
and the screen says heat pump system.
"FA F8"
• Fill the t(]nk completely with w(]ter. Press ENTER to stop
the (]l(]rm (]nd then press POWER when the t(]nk h(]s been
filled.
The heate r isbeePing There is on issue with the
and the screen flashes water heater that requires
an error code immediate attention.
The water heater is Unit is not receiving 240VAC
beeping and the screen as intend.
flashes, "bAd linE', ........
Hot Water has a rotten Certain water supplies with
egg or sulfur smell high sulfate content will react
with the anode rod that is
present in oil water heaters
for corrosion protection of
the tank.
unit is not making If unit is using electric
normal sounds resistanceelements, it will
not make fan or compressor
sounds.
2O
• Follow the instructions on how to remove (]nd cleon the
filter on p(]ge 12.
• The unit will (]utom(]tic(]lly switch to (]nother (]v(]il(]ble
mode to ensure you continue to hove hot w(]ter. Cont(]ct
service immedi(]tely (]nd give them the codes listed on the
displ(]y screen.
• The he(]ter m(]y switch to (]nother (]v(]il(]ble he(]ting mode.
Cont(]ct service immedi(]tely. To stop the beeping noise
(unless error code F2, Fll or bAd linE)press either the UPor
down (]rrow button (]nd the (]l(]rm will stop (]nd the displ(]y
will go b(]ck to norm(]l (set temper(]ture).
Turn off power to w(]ter he(]ter (gener(]lly(it the bre(]ker
p(]nel). Then re(]d "Electric(]l Connections" section of
Inst(]ll(]tion Instructions, see p(]ge 16. Then, cont(]ct the
inst(]ller to verify electric(]l input to the w(]ter he(]ter.
The odor con be reduced or elimin(]ted in most w(]ter
he(]ters by repl(]cing the (]node rod with less-(]ctive
m(]teri(]l rod. In some c(]ses,on (]dded step of
chlorin(]ting the w(]ter he(]ter (]nd (]11 hot w(]ter lines m(]y
be necess(]ry, cont(]ct your Ioc(]l w(]ter profession(]l or
plumber for options (]nd instructions. Coil GE(it
1.888.4GEHEWH(1.888.443.4394)to le(]rn how to purch(]se
this repl(]cement (]node rod. A qu(]lified servicer or
plumber should do this repl(]cement. Use of (] non-GE
(]pproved (]node rod, or oper(]ting the w(]ter he(]ter
without (] GE (]pproved (]node rod will VOID the w(]rr(]nty.
• Check mode of unit.
For Service, please call 1.888.4GE.HEWH (1.888.443.4394)