Idiomas disponibles
Idiomas disponibles
SAFETY WARNINGS AND PRECAUTIONS
WARNING: WHEN USING TOOL, BASIC SAFETY PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF PER-
SONAL INJURY AND DAMAGE TO EQUIPMENT.
Read all instructions before using this tool!
WARNING!
READ AND UNDERSTAN D ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in electric shock, fire, and/or
serious injury.
SAVE THESE INSTRUCTIONS
WORK AREA PRECAUTIONS
•
Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.
•
Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases, or dust. Power tools create sparks which may ignite
the dust or fumes.
•
Keep bystanders, children, and visitors away while operating a power tool. Dis-
tractions can cause you to lose control. Protect others in the work area from
debris such as chips and sparks. Provide barriers or shields as needed.
ELECTRICAL SAFETY
•
Grounded tools must be plugged into an outlet properly installed and grounded
in accordance with all codes and ordinances. Never remove the grounding prong
or modify the plug in any way. Do not use any adapter plugs. Check with a qua-
lified electrician if you are in doubt whether the outlet is properly grounded. If
the tool should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user.
•
Double insulated tools are equipped with a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install a polarized outlet. Do not change the plug in any
way. Double insulation eliminates the need for the three wire grounded power
cord and grounded power supply system.
•
Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and
refrigerators. There is an increased risk of electric shock if your body is ground-
ed.
•
Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
•
Do not abuse the Power Cord. Never use the Power Cord to carry the tool
or pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp
edges, or moving parts. Replace damaged Power Cords immediately. Damaged
Power Cords increase the risk of electric shock.
22
EN
Rev. 28.04.2022
•
When operating a power tool outside, sue an outdoor extension cord marker
"W-A" or "W". These extension cords are rated for outdoor use, and reduce the
risk of electric shock.
PERSONAL SAFETY
•
Stay alert. Watch what you are doing, and use common sense when operating a
power tool. Do not use a power tool while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while operating power tools
may result in serious personal injury.
•
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or
long hair can be caught in moving parts.
•
Avoid accidental staring. Be sure the Power Switch is off before plugging in. Car-
rying power tools with your finger on the Power Switch, or plugging in power
tools with the Power Switch on, invites accidents.
•
Remove adjusting keys or wrenches before turning the power tool on. A wrench
or a key that is left attached to a rotating part of the power tool may result in
personal injury.
•
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the power tool in unexpected situations.
•
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
•
Use clamps (not included) or other practical ways to secure and support the
workpiece to a stable platform. Holding the work piece by hand ro against your
body is unstable and may lead to loss of control.
•
Do not force the tool. Use the correct tool for your application. The correct tool
will do the job better and safer at the rate for which it is designed.
•
Do not use the power tool if the Power Switch does not turn it on or off. Any
tool that cannot be controlled with the Power Switch is dangerous and must be
replaced.
•
Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive safety
measures reduce the risk of starting the tool accidentally.
•
Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
•
Maintain tools with care. Keep cutting tools maintained and clean. Properly
maintained tools are less likely to bind and are easier to control. Do not use a
damaged tool. Tag damaged tools "Do not use" until repaired
•
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
•
Use only accessories that are recommended by the manufacturer for your mo-
del. Accessories that may be suitable for one tool may become hazardous when
used on another tool.
Rev. 28.04.2022
EN
23
