Idiomas disponibles
Idiomas disponibles
Washer
Diagnostic
Modes
To enter the "Washer Diagnostic Mode," first enter "Start
Operating Set-up." Then press and hold the QUICK CYCLE
button for 1 second while in set-up code 6, anytime a diagnostic
code is present, or while dAS displays if operating with Maytag
Data Acquisition set-up.
On entry to diagnostic mode the entire display will flash, a
cycle in process is canceled, money in escrow is cleared, and
diagnostic codes are cleared. If a diagnostic code persists,
it must be corrected before the following cycle options are
permitted.
There are five possible ways to initiate cycle activity from
diagnostic mode as follows:
1. Washer Cleanout cycle - With the entire display flashing, this
cycle is started by pressing the BRIGHTS button.
Use the Washer Cleanout cycle once a month to keep the
inside of your washer fresh and clean. This cycle uses
a higher water level. Use with liquid chlorine bleach to
thoroughly clean the inside of the washer. This cycle should
not be interrupted.
IMPORTANT:
Do not place garments or other items in the
washer during the Washer Cleanout cycle. Use this cycle with
an empty wash drum.
2. Cycle Credit - With the entire display flashing, a cycle may
be credited by pressing the PERM. PRESS button (CC will
display). When the service mode is exited, "SELECT CYCLE"
will be displayed unless the end-of-cycle
door opening is
required.
3. Manual Overview Test - With the entire display flashing, this
cycle is started by pressing the WHITES button. This cycle
provides more typical full length fills, tumbles, drains, and
dispenser actuator movement, allowing for a more thorough
analysis of the washer operation, including pressure switch
behavior.
4. Quick Spin Cycle - With the entire display flashing, this
cycle is started by pressing the COLORS button. This cycle
provides a method to quickly drain and spin (remove water
from the washer) if desired.
5. Quick Overview Test - With the entire display flashing, this
cycle is started by pressing the DELICATES AND KNITS
button. This cycle provides a quick verification that the cold
and hot water valves, dispensers, and pump motor are
working, as well as dispenser actuator movement.
It also
includes door lock, drain, and spin operations.
Pressing the QUICK CYCLE button will exit diagnostic mode
and cancel a diagnostic cycle in process.
DIAGNOSTIC
CODES
If one of the following has occurred, the appropriate
diagnostic
code will be in the display.
d5
Blocked coin 1 or coin drop control circuit failure (coin
recognition
and price display disabled while blockage
persists).
PN Models Only: Set-up mode J. should be set
to d
to eliminate coin related diagnostic codes.
d9
Low voltage detected for 8 seconds.
d13
Blocked coin 2 or coin drop control circuit failure (coin
recognition
and price display disabled while blockage
persists).
F20
Slow Fill. The washer will not detect water input for 4 rain.
Pressure switch failure or no water inlet. This code is
reported as d8 on d7.
F22
The door is not able to lock. Door lock error or someone
trying to start the washer, by pressing the door switch
with the finger. This code is reported as dl 7 on Accu Trac.
(For any other codes, check supplied Technical Sheet)
SERVICE ACCESS CODE
This code can be entered to access service mode without
removing the console. It only functions on washers set up for
0 vend price without any Special Pricing set-up, and the Coin/
Debit Option must be set to "J. d". If the washer is not in failure
mode, the door must be opened to proceed. Service Access
Code contains 6 steps and some are timed. Using only the three
bottom buttons (numbered 1,2, and 3 from left to right):
1. Press 2 for longer than 2 seconds but less than 10 seconds.
2. Press 1 & 3 together for 2 seconds, then release.
Displays S 3.
3. Press 1 & 2 together, then release. Displays S 4.
4. Press 2 & 3 together, then release. Displays S 5.
5. Press 2, then release. Display shows "codE".
6. Wait at least 2 seconds, but not more than 15 seconds, then
press in succession: 3, 2, 1, 3.
NOTE: If the Service Access Code procedure is not completed
properly, as noted above, there is a 15 second delay before it can
be attempted
again.
There are 3 options to exit from the Service Mode:
1. From Set-up Code 8, press button #1 for 4 seconds.
2. Wait 2 minutes without touching any buttons (without
diagnostic modes running).
3. Power down the washer, then reapply power.
WASHER HELP MODE
This mode is entered by pressing the PERM. PRESS button while
in special pricing option mode 2.XX (or while dAS displays if
operating with Maytag Data Acquisition
set-up).
In help mode, other display symbols and elements are mapped to
reflect the state of various inputs and outputs as follows:
Display Symbol
Description
Wash
Water sensed at wash level.
*
Low voltage present (below about
90 VAC).
° (Circle above digit)
Door closed.
DOOR LOCKED
Door sensed locked.
COLD
Cold water relay on.
HOT
Hot water relay on.
OR
Door unlocked.
AVAILABLE
Drain pump ON.
NOTE: A Technical Sheet is supplied taped to inside of lower
front panel, which includes fault codes and a washer schematic
diagram.
15
