Idiomas disponibles
Idiomas disponibles
20
en
Emission values for vibration
Vibration
Classification according to per-
formance class
STARLOCK
STARLOCK PLUS
K
a
* These values are based on a no-load measurement with max-
imum speed stage (6). In each case, the application tool corre-
sponds to the highest mass inertia of its performance class.
Operating Instructions.
Do not use accessories not specifically intended and
recommended for this power tool by Berner. The use
of non-original Berner accessories can lead to
overheating of the power tool and destroy it.
Changing the tool (see pages 6/7).
Do not switch the power tool on while the clamp-
ing lever is open. Otherwise there is danger of
crushes or contusions to the hand and fingers.
Do not reach into the area of the clamping jaws.
Otherwise there is danger of crushes or contu-
sions to the fingers.
Charge-control Indicator on the Battery
(see page 8).
The charge condition can be indicated by the green
LEDs of the charge-control indicator on the battery.
Press the charge-control indicator button
to indicate the charge condition.
When no LED lights up after pressing the charge-con-
trol indicator button, the battery is defective and must
be replaced.
Additional operating instructions.
Do not actuate the clamping lever while the power
tool is running. Otherwise there is danger of
injury.
Do not operate the power tool with with open
clamping jaws and without an application tool!
This could damage the power tool.
When the clamping jaws are open before the
application tool is inserted, pivot the clamping
lever toward the front and then back again. The
clamping jaws are closed now. The application
tool can be inserted.
Guide the power tool toward the work piece only
when switched on.
The application tool can be offset in 30° steps and fas-
tened in the most favourable working position.
The self-start prevention lock prevents the power tool
from automatically starting when the battery is inserted
while the on/off switch is set to on.
If the power tool shuts off without the switch being
actuated, switch the power tool switch off, remove the
battery and reattach it.
Notes on sanding.
Press the power tool with the sanding sheet briefly and
firmly against a flat surface and briefly switch the power
tool on. This provides for good adhesion and prevents
Weighted
premature wear.
acceleration*
When only one tip or corner of the sanding sheet is
2
3.6 m/s
worn, it can be removed again and reattached turned by
2
120°.
7.0 m/s
Work with the entire surface of the sanding plate, not
2
1.5 m/s
only with the tip.
When sanding with small triangle sanding plates, select
a high oscillating frequency (electronics level 4 – 6);
when sanding with the round sanding plate and the
large triangle sanding plate, select a moderate oscillating
frequency (max. electronics level 4).
Sand with continuous motion applying moderate pres-
sure. Applying excessive pressure does not increase the
rate of removal, it only wears off the sanding sheet
faster.
Notes on sawing.
Select a high oscillating frequency. Round saw blades
can be released and clamped offset again, to allow for
uniform wearing off.
Notes on scraping.
Select a moderate to high oscillating frequency.
Repair and customer service.
electricians, as improper maintenance can result in con-
siderable hazards for the user.
or
tool. Blow out the interior of the power tool via the
ventilation slots frequently with dry and oil-free com-
pressed air.
When working gypsum-containing materials, dust can
settle within the power tool and switch element, which
can harden in connection with humidity. This can
impair the switching mechanism. Blow out the interior
of the power tool via the ventilation slots and the
switch element frequently with dry and oil-free com-
pressed air.
For storage of the power tool, remove the application
tool and shut the clamping lever.
Products that have come into contact with asbestos
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable
country-specific regulations for such disposal.
Renew stickers and warning indications on the power
tool when aged and worn.
The current spares parts list for this power tool can be
found on our website at www.berner.eu.
Use only original spare parts.
If required, you can change the following parts your-
self:
Application tools
Please observe that power tools may only be
repaired, maintained and inspected by qualified
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power
