DeWalt DCD703 Traducido De Las Instrucciones Originales página 21


WARNING: Before assembly, lock the power unit by setting
the forward/reverse slider to the center position and remove the
battery from the tool. Remove any accessory from the attachment
before removing or installing the attachment.
1. Pull back on the locking sleeve
direction of the arrow.
2. Slide the attachment onto the spindle
the slots 20 on the attachment with the lugs
the spindle.
nOTE: Once on the spindle you may have to rotate the
attachment a small bit side to side so the slots align with
the lugs. The 10 mm chuck attachment
slots to align.
3. To remove the attachment, pull back on the locking sleeve
in the direction of the arrow and remove the attachment from
the spindle.
nOTE: The 6.35 mm hex right angle attachment
additional attchments to be installed on its spindle. With
the 6.35 mm hex right angle attachment installed on the
tool follow instruction 1 and 2 of this section to install
additional attachments.
nOTE: Only use attachments that are specifically designed
for and compatible with the power unit. Refer to individual
attachment instruction manuals for specific safety warnings and
operating instructions before operating attachments with the
power unit.
Installing a Bit or Accessory into a Keyless Chuck
(Fig. E)

WARNING: Do not attempt to tighten drill bits (or any other
accessory) by gripping the front part of the chuck and turning
the tool on. Damage to the chuck and personal injury may result.
Always lock off trigger switch and disconnect tool from power
source when changing acces sories.

WARNING: Always ensure the bit is secure before starting
the tool. A loose bit may eject from tool causing possible
personal injury.
Your tool features a keyless chuck with one rotating sleeve
one-handed operation of the chuck. To insert a drill bit or other
accessory, follow these steps.
1. Turn tool off and remove battery pack.
2. Grasp the black sleeve of the chuck with one hand and
use the other hand to secure the tool. Rotate the sleeve
counterclockwise far enough to accept the desired accessory.
3. Insert the accessory about 19 mm into the chuck and tighten
securely by rotating the chuck sleeve clockwise with one hand
while holding the tool with the other. Your tool is equipped
with an automatic spindle lock mechanism. This allows you to
open and close the chuck with one hand.
Be sure to tighten chuck with one hand on the chuck sleeve and
one hand holding the tool for maximum tightness.
To release the accessory, repeat steps 1 and 2 above.
Installing a Bit or Accessory with No Attachment
(Fig. E)
You can use your tool without installing an attachment.
Insert a hex bit directly into the spindle
place magnetically.
Speed Selection (Fig. A)
The tool features two speed settings for greater versatility
nOTE: Do not change speeds when the tool is running.
18 on the attachment in the
19 , aligning
21 around
8 does not have any
9 allows
14
. It is held in
19
Always allow the tool to come to a complete stop before
changing speed.
1. To select speed 1 (high torque setting), turn the tool off and
permit it to stop. Slide the speed selector
the chuck).
2. To select speed 2 (high speed setting), turn the tool off and
permit it to stop. Slide the speed selector
the chuck).
If the tool does not change speeds, confirm that the speed
selection switch is completely engaged in the forward or
back position.
Mode Selection (Fig. A)
The mode selection collar
operating mode depending upon the planned application.
To select, rotate the collar until the desired symbol aligns with
the arrow.
symbol
1–15
Variable Speed Trigger and Forward/Reverse Control
Button (Fig. A)
The tool is turned on and off by pulling and releasing the
variable speed trigger switch
depressed, the higher the speed of the tool. Your tool is
equipped with a brake. The chuck will stop as soon as the
trigger switch is fully released.
A forward/reverse control button
direction of the tool and also serves as a lock-off button.
• To select forward rotation (clockwise), release the trigger and
depress the forward/reverse control button on the right side of
the tool.
• To select reverse (counterclockwise), depress the forward/
for
reverse control button on the left side of the tool.
nOTE: The centre position of the control button locks the tool
in the off position. When changing the position of the control
button, be sure the trigger is released.
nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
nOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and
does not indicate a problem.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect battery pack before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Check for damage to the tool, parts or accessories which may
have occurred during transport.
6 back (away from
forward (toward
6
can be used to select the correct
5
Mode
Drilling
Screwdriving (higher number = greater torque)
3 . The farther the trigger is
determines the rotational
4
EnGLIsH
21