Idiomas disponibles
Idiomas disponibles
Initial Start-up
Do not use coffee powder during this procedure!
1. Fill the water tank with clean, fresh water up to the MAX
mark.
2. Insert the filter holder.
3. Place a suitable container (heat-resistant / approx. 250 ml)
under the steam nozzle.
4. Switch on the appliance. The appliance starts heating.
The heating plate becomes hot.
5. Press the
button, wait a moment, the brewing pro-
cess starts and water flows out.
WARNING: Risk of Burns!
The water in the vessel is hot.
6. When the appliance stops pumping water, the process
is complete. Pour away the water that has been pumped
out.
- A noise may occur when the water is pumped out, this
is normal as the appliance is deflating. The noise will
disappear after about 20 seconds.
7. Place the empty receptacle under the steam nozzle.
8. Press the
button. Wait until the heating process for
steam generation is complete. Observe the scale on the
temperature display.
9.
WARNING: Risk of Burns!
Hot steam comes out of the steam nozzle.
To generate steam, turn the control to the position
When a steady stream of water emerges from the steam
nozzle, turn the control back to the position .
WARNING: Risk of Burns!
• When moving the steam nozzle after steaming,
always grasp it by the black rubber handle!
• The water in the vessel is hot.
10. The appliance is now ready for operation.
Insert and Remove Filter Inserts
• There are guide lugs on the filter inserts. These must be
inserted into the notch of the filter holder. Then turn the
filter insert by 90 degrees so that it does not fall out when
emptying later.
• To be able to remove the filter insert, it must be turned in
such a way that the guide nose is again in the notch of
the filter holder. Now the filter insert can be removed.
Program Individual Coffee Quantity
You have the option of changing the factory-set coffee
quantity. Two standard quantities for one cup (
for two cups (
) are set at the factory. To change these
according to your wishes, proceed as follows:
1. Fill the water tank with sufficient water and reinsert it.
2. Fit the filter holder without the coffee grounds.
3. Place a cup under the brew head.
PC-ES1267_IM
4. Insert the mains plug into a socket and switch on the
appliance.
5. Wait until all control lamps light up. Then press and hold
the button for the cup whose standard quantity is to be
set. You will hear a beep. Only the indicator lights of the
button and the button whose standard quantity is to
be set light up. Press the button on the cup again to start
the cycle.
6. As soon as the desired quantity is reached, press the
button again.
- A beep sounds and all control lamps light up to
indicate that the programming has been successfully
saved The appliance is now ready for use again.
Delete Programmed Coffee Quantity
Proceed as follows to delete the individually programmed
coffee quantity and restore the standard quantity:
1. Fill the water tank with sufficient water and reinsert it.
2. Fit the filter holder without the coffee grounds.
3. Place a cup under the brew head.
4. Insert the mains plug into a socket and switch on the
appliance.
5. Press and hold both buttons (
A signal tone sounds, indicating that the programming
has been deleted.
- The factory settings are restored and your appliance is
immediately ready for use again.
/ .
Espresso Preparation
1. Fill the water tank with sufficient water and reinsert it.
The water level must be between the MIN and MAX
marks.
2. Switch on the appliance. A beep sounds. The control
lamp for the
lamps flash. The appliance starts heating. The heating
plate becomes hot.
3. Select a filter insert (17 / 18). Place it in the filter holder.
Make sure that the filter insert is turned 90 degrees so
that it does not fall out when emptying later. See previ-
ous chapter "Insert and Remove Filter Inserts".
4. Fill the filter insert with espresso grounds. Use the
measuring spoon provided (one measuring spoonful =
1 cup). Distribute the coffee grounds evenly and press
down lightly with the tamper. Clean the edge of the filter
holder.
5. Fit the filter holder to the brew head. Make sure that the
filter holder is firmly seated in the brew head.
6. When the required brewing temperature is reached, all
control lamps light up. Place the cup(s) under the brew
) and
head on the drip tray.
7. Press the
through the filter.
8. When no more coffee flows, remove the cup(s).
- Remove the filter holder after each preparation. This
prolongs the life of the rubber seal in the brew head.
/
) simultaneously.
button lights up while the other control
or
button. The hot water is pressed
22.11.23
17
