Idiomas disponibles
Idiomas disponibles
10.2
Filling up with fuel (Fig. 10)
DANGER
Risk of fire and explosion!
When filling, fuel may ignite and even explode. This can
lead to severe burns or death.
• Switch off the engine and let it cool down.
• Keep heat, flames and sparks away.
• Only fill up with fuel outdoors.
• Wear protective gloves.
• Avoid contact with skin and eyes.
• Start the product at a distance of at least 3 m from the fu-
el filling point.
• Watch out for leaks. If fuel is leaking, do not start the en-
gine.
ATTENTION
The product is delivered without fuel. It is there-
fore essential to fill with fuel before commission-
ing. Use Super E10 petrol for this.
1. Clean the area surrounding the filling area. Impurities in
the fuel tank (8) lead to operational faults.
2. Carefully open the tank cover (7) so that any possible
overpressure can be relieved.
3. Fill the fuel tank (8) with fuel using a funnel (not included
in scope of delivery). Note the max. filling capacity of
0.85 litres. Carefully fill the fuel up to the lower edge of
the filling port.
4. Close the fuel filter cap (7) again. Ensure that the fuel cap
is tightly sealed.
5. Clean the fuel filter cap (7) and the surroundings.
6. Check the fuel tank (8) and fuel lines for leaks.
7. Start the product at a distance of at least 3 m from the fu-
el filling point.
11
Start-up
NOTE
Some noise pollution from this product is un-
avoidable. Postpone noisy work to approved and
designated times. If necessary, adhere to rest pe-
riods and limit the duration of work to the bare
minimum.
For your personal protection and the protection
of nearby persons, wear suitable hearing protec-
tion.
11.1
Blade stop device
Before each use, you must check the blade stop device. Start
the engine as described in 12.2.
1. Release the engine brake lever (2). The engine switches
off and the blade (19) is braked.
2. The blade (19) must stop within 7 seconds.
11.2
Preparing the area to be mowed
1. Before mowing, carefully examine the area.
8
|
GB / IE / NI / CY / MT
2. Remove stones, sticks, bones, wires, toys and other ob-
jects that may be ejected by the product.
3. Ensure that no other people are present on the surface to
be mowed.
11.3
Setting the cutting height (Fig. 7+8)
ATTENTION
Adjust the cutting height only when the engine is
switched off and the plug boot has been pulled.
• The cutting height is adjusted via the wheels (11). Three
different cutting heights can be set.
• In dense, tall grass, set the highest cutting level and mow
more slowly. A high cutting height should be selected for
the first cut of the season. Adjust the cutting height so that
the product is not overloaded.
• Set the cutting height depending on the actual length of
the lawn.
• Carry out several passes so that a maximum of 4 cm of
lawn is removed at a time.
• The correct cutting height for
– ornamental grass is about 30 - 45 mm
– utility turf about 40 - 65 mm.
12
Operation
Working instructions
• Only cut with sharp, flawless mowing blades (19) so that
the blades of grass do not fray and the lawn does not
turn yellow.
• To achieve a clean cut, guide the lawnmower in the
straightest possible paths. These strips should always
overlap by a few centimetres so that no patches remain.
• Keep the underside of the lawnmower housing clean and
be sure to remove grass debris. Deposits make the start-
ing process more difficult, impair cutting quality and
grass discharge.
• On slopes, the cutting path should be made perpendicu-
lar to the slope.
It is possible to prevent the lawnmower from slipping by
lifting it upwards at an angle.
12.1
Mowing with the grass collection
basket
ATTENTION
Do not operate the product without the grass collection bas-
ket fully attached.
ATTENTION
Only remove or attach the grass collection basket when the
engine is switched off and the blade is stationary.
12.1.1
Inserting the grass collection basket (16)
(Fig. 11)
1. Lift the rear discharge flap (15).
2. Hold the grass collection basket (16) by the carrying han-
dle.
3. Hang the grass collection basket (16) in the grass collec-
tion basket suspension provided at the rear of the prod-
uct.
