Philips CD 303 Instrucciones De Manejo página 5

Beginning at a n y Specific
Track (GO-TO mode)
To start a track other than
play with
must locate the track
the first, you
TRACK
required on the Display. To
do this, SELECT
you press the
the first TRACK LED will
Display
begin to flash. Press the SELECT
key again and the flashing TRACK
LED will move forward one
Display
place. You press the SELECT
successively until the flashing
TRACK LED indicates the
Display
track.
required Alternatively, you
can hold the SELECT key down and
let the flashing TRACK Display LED
run through until it reaches the track
required. The TRACK Display LED
will continue to flash under the
chosen track for about 10 seconds,
must press
during which time you
the PLAY key. The PROGRAM Dis‑
LEDs will go out one after
play
another until the chosen track is
indicated, then play will begin.
You can also use the GO-TO mode
after play has begun, e.g. to skip a
Repeating t h e Disc
(REPEAT)
If you want to hear the whole disc
again, press the REPEAT key be‑
fore ends. The REPEAT LED
play
will play con‑
will light, and the disc
tinuously until you either press the
REPEAT key again, or press the
STOP key or the OPEN/CLOSE
key.
a Particular
Finding
Passage (REV and FWD)
During play, you can quickly locate
music passage
a particular in a
track with the REV and FWD
keys.
If you hold the REV key down, the
runs back towards the
laser pick-up
hold the FWD
beginning; if you
down, the laser pick-up runs
towards the end. When release
you
the key, once. By
play restarts at
pressing the keys alternately, you
can find any part of any passage.
lf, by pressing the FWD
key, you
take the laser pick-up into the run‑
out of the last track, the ERROR
LED will flash and
the disc will stop.
Interrupting Play (PAUSE)
For short
play interruptions, you
press the PAUSE key. The disc car‑
ries on spinning, but the sound
stops, and the PAUSE LED
lights.
If you press the PAUSE key again,
or the PLAY key, the sound restarts
at the exact point where it was
interrupted. The PAUSE LED goes
out.
Stopping Play
(STOP or OPEN/CLOSE)
To before the end of the
stop play
disc, you press the STOP key or
the OPEN/CLOSE
key. The disc
and all the LEDs
stops, in the
PROGRAM Display relight, while the
TRACK Display LED goes out.
key;
key
specific track. Play will then be
interrupted from the time the PLAY
key is pressed until the
chosen track is reached.
If, by mistake, you select a track
higher than the highest track num‑
ber on the disc, the ERROR LED will
flash. This will
happen immediately
with a disc that is
already playing, or
after the contents list has been read
with a disc that has not
Play will then begin with
track on the disc.
In the first case the disc will
to the end before stopping, in the
other two cases play will stop
once. The REPEAT LED will go out.
During repeat the PROGRAM
Display LEDs remain alight and
the TRACK
Display LED
the progress of play.
The same will happen if, by
thing
pressing the REV key, you take the
laser pick-up beyond the run-in of
the first track. In either case, you
can restart the disc by pressing the
PLAY
key.
It is possible to use the REV
FWD keys to run to any point on
k e y
disc. Depending on the position of
the laser pick-up, however, this can
take quite a long time.
first to use the GO-TO mode to find
the required track first, and only
then use the REV and FWD
to
can
If you allow more than
to elapse between choosing the
quired track and pressing the PLAY
newly the microprocessor in the
key,
will assume that you have
player
changed your mind,
mand will not be executed; the
TRACK Display LED will
flashing
out.
If you accidentally go past the re‑
quired track, hold
started. SELECT until the TRACK Dis‑
yet key
the first LED runs
play
returns to track 1, then run forward
to the track required.
play on
at
only
indicates
and
the
It is quicker
keys.
10 seconds
re‑
and the com‑
go
down the
and
right through