Makita 4341T Manual De Instrucciones página 8

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 26
Removing saw blade
CAUTION:
When you remove the saw blade, be careful not to hurt
your fingers with the top of the blade or the tips of work-
piece.
Open the tool opener to the position shown in the figure.
Pull the saw blade out toward the base. (Fig. 3)
NOTE:
Occasionally lubricate the roller.
Selecting the cutting action (Fig. 5)
This tool can be operated with an orbital or a straight line (up and down) cutting action. The orbital cutting action
thrusts the blade forward on the cutting stroke and greatly increases cutting speed.
To change the cutting action, just turn the cutting action changing lever to the desired cutting action position.
Refer to the table below to select the cutting action.
Position
Straight line cutting action
0
Small orbit cutting action
I
II
Medium orbit cutting action
Large orbit cutting action
III
Switch action (Fig. 6)
CAUTION:
Before plugging in the tool, always check to see that the
tool is switched off.
To start the tool, slide the switch lever to the "I" position.
To stop the tool, slide the switch lever to the "O" position.
Speed adjusting dial (Fig. 7)
For 4341CT, 4341FCT only
The tool speed can be infinitely adjusted between 800
and 2,800 strokes per minute by turning the adjusting
dial. Higher speed is obtained when the dial is turned in
the direction of number 5; lower speed is obtained when
it is turned in the direction of number 1. Refer to the table
below to select the proper speed for the workpiece to be
cut. However, the appropriate speed may differ with the
type or thickness of the workpiece. In general, higher
speeds will allow you to cut workpieces faster but the ser-
vice life of the blade will be reduced.
Workpiece to be cut
Wood
Mild steel
Stainless steel
Aluminum
Plastics
CAUTION:
The speed adjusting dial can be turned only as far as 5
and back to 1. Do not force it past 5 or 1, or the speed
adjusting function may no longer work.
8
Cutting action
Number on adjusting dial
4 – 5
3 – 5
3 – 4
3 – 5
1 – 4
Hex wrench storage (Fig. 4)
When not in use, the hex wrench can be conveniently
stored.
Applications
For cutting mild steel, stainless steel and plastics.
For clean cuts in wood and plywood.
For cutting mild steel, aluminum and hard wood.
For cutting wood and plywood.
For fast cutting in aluminum and mild steel.
For fast cutting in wood and plywood.
For 4341CT, 4341FCT only
The tools equipped with electronic function are easy to
operate because of the following features.
Constant speed control
Electronic speed control for obtaining constant speed.
Possible to get fine finish, because the rotating speed is
kept constant even under load condition.
Soft start feature
Safety and soft start because of suppressed starting
shock.
Lighting up the lamps (For 4341FCT only)
CAUTION:
Do not look in the light or see the source of light directly.
To turn on the lamp, pull the trigger. Release the trigger
to turn it off.
NOTE:
Use a dry cloth to wipe the dirt off the lens of lamp. Be
careful not to scratch the lens of lamp, or it may lower the
illumination.
Operation (Fig. 8)
CAUTION:
Always hold the tool base flush with the workpiece. Fail-
ure to do so may cause blade breakage, resulting in a
serious injury.
Turn the tool on and wait until the blade attains full speed.
Then rest the tool base flat on the workpiece and gently
move the tool forward along the previously marked cut-
ting line. When cutting curves, advance the tool very
slowly.
Tabla de contenido
loading

Este manual también es adecuado para:

4341ct4341fct

Tabla de contenido