Motor Brushes; Protecting The Environment - DeWalt D25032 Traducido De Las Instrucciones Originales

EngLIsh
8. Always switch off the tool when work is finished and
before unplugging.
Rotary Drilling (Fig. A)
1. Hold down the mode selector button
selector switch 4 to the "rotary drilling" position.
2. Depending on your tool, follow either of the following
instructions:
- D25032, D25033, D25133, D25143: Fit the chuck adapter/
chuck assembly.
- D25134, D25144: Replace the SDS plus® tool holder with the
keyless chuck.
3. Proceed as described for hammerdrilling.

WARNING: Never use standard chucks in the
hammerdrilling mode.
Screwdriving (Fig. A)
1. Hold down the mode selector button
selector switch 4 to the rotary drilling position.
2. Select the direction of rotation.
3. Depending on your tool, follow either of the
following instructions:
- D25032, D25033, D25133, D25143: Insert the special
SDS plus® screwdriving adaptor for use with hexagonal
screwdriver bits.
- D25134, D25144: Replace the SDS plus® tool holder with the
keyless chuck.
4. Insert the appropriate screwdriver bit. When driving slotted
head screws always use bits with a finder sleeve.
5. Gently press the variable speed switch
to the screw head. In reverse (LH) rotation the tool speed is
automatically reduced for easy screw removal.
6. When the screw is flush with the workpiece, release
the variable speed switch to prevent the screw head from
penetrating into the workpiece.
Chipping and Chiselling (Fig. A)
D25033, D25133, D25134, D25143, D25144
1. Hold down the mode selector button
selector switch to the "hammering only" position.
4
2. Insert the appropriate chisel and rotate it by hand to lock it
into position.
3. Adjust the side handle 8
4. Switch on the tool and start working.
5. Always switch off the tool when work is finished and
before unplugging.

WARNING:
• Do not use this tool to mix or pump easily combustible or
explosive fluids (benzine, alcohol, etc.).
• Do not mix or stir in flammable liquids labelled accordingly.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power source
before making any adjustments or removing/installing
attachments or accessories. Be sure the trigger switch is in the
OFF position. An accidental start-up can cause injury.
26
5 then set the mode
5 then set the mode
1 to prevent damage
5 then set the mode
as required.
• This machine is not user-serviceable. Take the tool to an
authorised D WALT repair agent after approximately 40 hours
e
of use. If problems occur before this time contact an authorised
D WALT repair agent.
e
• The tool will automatically switch off when the carbon
brushes are worn.

Motor Brushes

D WALT uses an advanced brush system which automatically
e
stops the drill when the brushes wear out. This prevents serious
damage to the motor. New brush assemblies are available
at authorised D WALT service centers. Always use identical
e
replacement parts.
Lubrication
Your power tool requires no additional lubrication.
Accessories and attachments used must be regularly lubricated around the SDS plus® fitment.
Cleaning

WARNING: Electrical shock and mechanical hazard.
Disconnect the electrical appliance from the power source before
cleaning.

WARNING: To ensure safe and efficient operation, always
keep the electrical appliance and the ventilation slots clean.

WARNING: Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool. These chemicals may
weaken the materials used in these parts.Use a cloth dampened
only with water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Ventilation slots can be cleaned using a dry, soft non-metallic
brush and/or a suitable vacuum cleaner. Do not use water or
any cleaning solutions. Wear approved eye protection and an
approved dust mask.
Optional Accessories

WARNING: Since accessories, other than those offered by
D WALT, have not been tested with this product, use of such
e
accessories with this tool could be hazardous. To reduce the risk
of injury, only D WALT recommended accessories should be used
e
with this product.
Various types of SDS plus® drill bits and chisels are available as
an option.
Consult your dealer for further information on the
appropriate accessories.

Protecting the Environment

Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
SDS plus® and SDS max® are registered trademarks of
Robert Bosch GmbH.