Metabo BE 650 Manual Original página 9

Original instructions
1. Declaration of Conformity
We, being solely responsible, hereby declare that
these drills/impact drills, identified by type and
serial number *1), meet all relevant requirements of
directives *2) and standards *3). Technical
documents for *4) - see page 3.
For UK only:
We as manufacturer and authorized person to
compile the technical file, see *4) on page 3,
hereby declare under sole responsibility that these
drills/impact drills, identified by type and serial
number *1) on page 3, fulfill all relevant provisions of
following UK Regulations S.I. 2016/1091, S.I. 2008/
1597, S.I. 2012/3032 and Designated Standards
EN 62841:2015, EN 62841-2-1:2018, EN IEC
63000:2018.
2. Specified Conditions of Use
SBE 650, SBE 650 Impuls:
The impact drill is suitable for non-impact drilling in
metal, wood, plastic and similar materials and
impact drilling in concrete, stone and similar
materials.
B 650, BE 650:
The drill is suitable for non-impact drilling into metal,
wood, plastic and similar materials.
BE 650, SBE 650, SBE 650 Impuls:
The machine is suitable for thread cutting and
screwdriving.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.
3. General Safety Information
For your own protection and for the
protection of your power tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Read the operating
instructions to reduce the risk of injury.
WARNING – Read all safety warnings,
instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Always include these documents when passing on
your power tool.
4. Special safety instructions
4.1 Safety instructions for all operations
a) Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
b) Use the auxiliary handle(s). Loss of control can
cause personal injury.
c) Brace the tool properly before use. This tool
produces a high output torque and without properly
bracing the tool during operation, loss of control
may occur resulting in personal injury.
d) Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory or fasteners may contact
hidden wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the
operator an electric shock.
4.2 Safety instructions when using long drill
bits
a) Never operate at higher speed than the
maximum speed rating of the drill bit. At higher
speeds, the bit is likely to bend if allowed to rotate
freely without contacting the workpiece, resulting in
personal injury.
b) Always start drilling at low speed and with
the bit tip in contact with the workpiece. At
higher speeds, the bit is likely to bend if allowed to
rotate freely without contacting the workpiece,
resulting in personal injury.
c) Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend causing breakage and loss of control,
resulting in personal injury.
4.3 Additional safety instructions
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes (e.g.
using a metal detector).
Avoid inadvertent starts by always unlocking the
switch when the plug is removed from the mains
socket or in case of a power cut.
Keep hands away from the rotating tool!
Remove chips and similar material only with the
machine at a standstill.
Caution must be exercised when driving screws into
hard materials (driving screws with metric or
imperial threads into steel)! The screw head may
break or high reverse torques may build up.
High forces are released if the tool jams or catches.
Always hold the machine firmly, adopt a steady
stance
and focus on your work.
Secure small workpieces, for example by clamping
them in a vice.
Reducing dust exposure:
WARNING - Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
ENGLISH en
9