YATO YT-83085 Manual De Instrucciones página 12

Messages communicated by the device to the user
The device communicates with the user, by means of indicator lamps and a buzzer signal.
Green indicator
No. Red indicator light
light
1
bliniking
bliniking
2 inactive active
3 bliniking inactive
5 active inactive
6 active inactive
Use of the product for charging portable devices
Before starting charging the device, see the documentation provided with the device to make sure that powerbanks can be used
for charging it.
Switch on the device by pressing the switch. Connect one of the plugs to the charging socket in the portable device to be charged.
Plug the other plug of the lead into one of the USB sockets in the product marked "OUTPUT" and designated with voltage rating.
Before connecting, check the value of voltage that can be supplied to the connected device.
The charging process will start.
The power supply effi ciency of the socket has been defi ned in the technical data table.
Products featuring multiple sockets can be used to simultaneously charge many devices, using the sockets.
When charging is complete, disconnect the plug from the socket in the starter device and then from the charged device.
The product features a battery with a capacity specifi ed in the technical data table, which means that it can fully charge only de-
vices equipped with a battery the capacity of which is lower than the capacity of the battery in the product.
If the connected device features a battery with a capacity exceeding the capacity of the battery in the product, then the battery in
that device cannot be fully charged.
When charging, some of the energy accumulated in the product's battery will be lost, resulting from heat generation. This is a nor-
mal phenomenon, which means that we cannot assume that the product will fully charge a device with the same battery capacity
as the capacity of the battery in the product.
To switch off the unit, press and hold the switch for approximately 5 seconds.
Wireless (inductive) charging
The product has a built-in wireless charger. It allows batteries to be charged without connecting cables. Wireless charging will only
work on devices that support wireless charging. Before charging, make sure that the device has wireless charging functionality,
you can check this in the technical documentation supplied with the device or contact the manufacturer of the device.
NOTE! Some cases, covers, applicable to mobile devices may interrupt or prevent charging. If the case of the mobile
device is too thick, wireless charging may not work properly. Before starting wireless charging, remove all additional
items from the housing of the mobile device, in particular such as credit, transport and other cards, metal components,
magnets. If additional items are not removed, the charging of the mobile device may be disrupted, the device may
overheat, the device may be damaged or additional items such as a credit card may be damaged. Do not charge mobile
devices that are damaged, have an open or damaged battery compartment.
To start charging, ensure that the wireless charging area is in the up position and not obscured by other objects. Switch on the
device by pressing the switch. Place the device on the wireless charging area. Charging will start when the wireless charging
area of the product comes into contact with the charging coil of the mobile device. If wireless charging is not making progress, the
position of the device on the charging area should be corrected. When charging is complete, take the mobile device away from
the charging area immediately.
To switch off the unit, press and hold the switch for approximately 5 seconds.
Using the fl ashlight provided in the product
The product is equipped with an LED, which can be used as a fl ashlight to provide additional lighting of a small area or as a signal
lamp. The LED will illuminate when the switch is pressed three times. A single press of the button will change the lighting mode in
the following sequence: continuous light, fl ashing, SOS signal encoded in Morse code. The torch can be switched off by pressing
and holding the switch for approximately 5 seconds.
Product maintenance
The product does not require any special maintenance. Clean the product casing with a soft, dry cloth. Never immerse the product
in water or in any other liquid. Protect the product sockets against contamination. If the socket is dirty, try to clean it by blowing a
jet of compressed air stream into it, at a pressure not exceeding 0.3 MPa. Do not use any hard objects to clean the sockets, as
this can damage the socket or cause a short circuit.
O R I G I N A L
12
EN
Buzzer sound Description
no signal
Jump leads are connected
The jump leads and the battery in the vehicle have been connected. The device is ready to start
no signal
the engine.
no signal Low battery in the device.
steady The terminals of the jump leads are shorted.
steady Reversed polarity of the connected terminals of the jump leads.
I N S T R U C T I O N S