cecotec BOLERO COOLMARKET 2D 211 WHITE Manual De Instrucciones página 27

ENGLISH
3. PLACE OF INSTALLATION
1. Conditions for proper ventilation
The location you choose for the installation of the refrigerator must be properly ventilated and
away from heat sources. Do not place the refrigerator near heat sources, like a cooker hob or
pot, and avoid direct sunlight to ensure the cooling effect and save on energy consumption. Do
not place the refrigerator in a damp place to avoid rust or loss of power. The result of dividing
the amount of refrigerant load by the total space of the room in which the refrigerator is
installed must not be less than 8 g/m³.
Note:
The amount of refrigerant used by the refrigerator is specified on the appliance marking.
Heat dissipation space
2.
- During operation, the refrigerator releases heat into the environment. Therefore, you
should leave at least 30 mm of free space at the top chamber, more than 100 mm on both
sides, and more than 50 mm at the rear of the refrigerator.
- Dimensions in mm (Fig. 2):
W Depth Height A
540 551 1428 910
Note:
Figure 2 only illustrates the space required for the product.
Installation surface
3.
- Place the refrigerator on a solid, flat surface to keep it stable, otherwise vibrations and
noises will occur. When the refrigerator is placed on a carpet, straw mat, or polyvinyl
chloride, solid support plates should be placed under the refrigerator to avoid colour
change due to heat dissipation.
- It is necessary to maintain unobstructed ventilation around the appliance or in the
structure where it is installed.
Levelling
4.
Make sure you level your refrigerator with the front levelling feet. If it is not levelled, the door
sealing performance of the refrigerator will be affected, or it can even cause a malfunction.
Preparing for use
5. Waiting time
Once the refrigerator is correctly installed and clean, do not turn it on immediately, wait at
least 4 hours before connecting it to the power supply to ensure normal operation.
B O LE R O COOLM ARKET 2D 211 W H IT E
52
B C(°) E F
1054 130±5 50 100
6. Cleaning
Check the placement of the interior accessory parts and clean the inside of the refrigerator
with a soft cloth.
7. Switch-on
Connect the plug into a power socket to switch on the compressor. After one hour, open the
refrigerator door: if the temperature inside the refrigerator compartment has dropped, this
means the cooling system is running normally.
8. Food storage
After the refrigerator has been in operation for some time, the user may adjust its internal
temperature. Once the refrigerator has reached a suitable interior temperature, put in the food.
If the refrigerator is installed in a wet place, be sure to check if the earth wire and the circuit
breaker are working normally. If vibration noises occur due to contact of the refrigerator
with the wall or if the wall turns black due to air convection around the compressor, keep
the refrigerator further away from the wall. The installation of the refrigerator may cause
noise interference or image problems in mobile phones, landline phones, radio receivers, or
televisions near the refrigerator, so in this case, keep the refrigerator as far away from these
objects as possible.
Changing the door opening direction
1. Make sure the refrigerator is unplugged.
Lift up and remove the hinge cover, remove the three screws securing the top hinge to the
2.
door, then remove the hinge. Fig. 3
3. Remove the refrigerator-compartment door.
4. Remove the two screws securing the centre hinge. Fig. 4
Remove the freezer-compartment door.
5.
6. Remove the levelling foot from the left side of the refrigerator and set it aside for later
installation. Fig. 5
7. Remove the screws securing the bottom hinge on the right side of the refrigerator, then
remove the hinge. Fig. 6
8. Remove the washer and nut securing the pin shaft from the right-hand hole in the lower
hinge, then remove the shaft. Fig. 7
9. Insert the pin shaft into the left hole of the lower hinge, then secure the shaft with the
washer and nut. Fig. 8
10. Install the lower hinge on the left side of the refrigerator.
11. Install the removed levelling foot on the right-hand side of the refrigerator. Fig. 9
12. Remove the screw holding the refrigerator-compartment door stop on the lower-right
side, then remove the door stop and install it on the lower-left side. Fig. 10
13. Install the refrigerator-compartment door.
BOLERO COOLMARKET 2D 211 WHITE
ENGLISH
53