Idiomas disponibles
Idiomas disponibles
BLADE PERPENDICULAR TO THE SURFACE
Adjust the blade, checking it with a reference square at 90°
on the work surface.
DIVIDING BLADE
Carry out this adjustment whenever the blade is replaced and
at regular intervals.
Disassemble the protection and remove the plastic panel on
the work surface in the blade area.
Check that the distance between the blade teeth and the divi-
ding blade (fig.G pos.1) is as illustrated in fig. G.
Check that the vertical distance between the point of the
dividing blade and the top of the blade teeth is as illustrated in
Fig. G. For the adjustment loosen the nut (Fig. G pos.2), adjust,
re-fix and re-assemble the panel well with the screws and
blade protection. Check that the blade teeth are not touching
the protection.
PARALLEL GUIDE
Adjust the parallel guide so that it is parallel to the blade.
Observing the scale on the work surface, position the parallel
guide at the required distance and fix the position by lowering
the lever on the piece guiding square.
ADJUSTABLE PIECE GUIDING SQUARE
For orienting the cut at the required slope:
loosen the knob on the square, adjust it to the required angle
and re-fix the knob.
OPERATIONAL TIPS
IMPORTANT! Always use the personal protective equipment
required by safety regulations and the precautions listed
herein.
- Before starting the machine, check you have carried out all
the required adjustments and that the locks are correctly
tightened.
- Before starting to cut, wait for the blade to reach its maximum
number of revolutions.
- Remove all the work scraps, saw dust or anything caught
in the machinery only after switching off the machine and
when the blade is completely still.
- When you cut long pieces, assemble the work surface
extension device.
- When your hands are in the vicinity of the blade during cutting
operations, always use the relative piece pusher to push the
piece (Fig.F pos.1); you will thus protect your hands from
injury.
- Push the piece against the blade slowly and evenly so that
the blade speed does not reduce substantially.
- While cutting, keep the piece rested on the work surface and
the parallel or adjustable guide.
MAINTENANCE
IMPORTANT! Always unplug the machine from the mains
socket before proceeding with any type of inspection or
maintenance.
- Clean and maintain your machine regularly, to ensure that it
remains perfectly efficient and has a long working life.
- At the end of each job, clean the whole machine.
- Periodically check the state of wear of the blade, replacing
it when it shows signs of cracks, deformations or uneven
consumption.
- When cleaning the machine, only use a cloth and a brush.
Do not use any detergents or solvents as these may damage
the machine beyond repair.
- In the event that maintenance or repairs not specified in
these instructions are required, please contact an authorised
service centre.
IMPORTANT! The cutting part can cause serious injuries
use protection gloves!
- Use good quality blades with the same characteristics as
the machine based on its technical data – your retailer will
be able to help you make the correct choice. Also observe
any instructions provided with the equipment.
- Do not use blades if you do not know where they are from
or without technical specifications. They must show the
nominal dimensions, the number of teeth, the maximum
number of revolutions and the arrow indicating the rotation
direction.
- The number of revolutions and the dimensions are the basic
elements for making your choice. The number of revolutions
must always be higher or equal to that shown on the machi-
ne. The dimensions must be equal to those shown on the
machine.
- Use blades which conform to the regulations in force in the
country of use.
- Do not use HSS (high speed steel) blades or abrasive trun-
cating discs.
- Always carry out a simple visual check: there must be no
deformations, breakages or damages.
- Do not utilize damages blades.
Our company provides a complete series of blades suitable for
your machine, which you can buy from your retailer.
REPLACING THE BLADE (FIG. G)
IMPORTANT! Before replacing anything turn the switch to
the OFF "O" position (off) and unplug the machine from the
electric power supply.
IMPORTANT! After cutting the blade reaches high tempera-
tures: wait for it to cool down before replacing it.
IMPORTANT! Even if the blade has stopped, it is still very
sharp: use gloves to prevent serious injuries.
IMPORTANT! The assembly of the blade must be carried
out with absolute precision. Incorrect assembly causes
very serious danger.
When replacing the blade, proceed as follows. The operation
must be carried out by an expert; if in doubt please contact
an authorised service centre.
- Unplug the machine from the electric power supply.
- For correct reassembly, observe the various components
before proceeding.
- Raise the blade to the highest point (see chap. "CUT DEPTH
ADJUSTMENT").
- Remove the protection and the panel.
- Lock the disc-lock flange with the key provided and loosen
the screw (IMPORTANT! Left-handed screw, turn it clockwise
to unscrew it).
- Remove the screw and the flange; disassemble the blade
and replace it with a new one with the same characteristics
described in the technical specifications, taking care to
ensure that the blade has the arrow turned in the same
direction as that shown on the blade protection.
- Re-assemble the disc-lock flange and tighten the screw with
14
BLADE
