Idiomas disponibles
Idiomas disponibles
IMPORTANT! Before carrying out the following operations,
make sure that the machine's plug is disconnected from
the mains.
The machine is supplied with some disassembled components
and before using it, it must be cleaned and installed.
When choosing where to put the machine, the following should
be considered:
- that the planned position is not damp and is protected from
atmospheric agents.
- that the area where it will be placed is completely flat, on an
anti-slip floor and with appropriate load capacity.
- that there should be a large operational area around the
machine free from obstacles.
- that the room should be attended in order to prevent free
access.
- that there needs to be good lighting.
- that it needs to be positioned close to the general differential
switch.
- that the power supply system is earthed and conforms to
the standards.
- that the room temperature should be between 10° and
35°C.
- that the work environment is not in an explosive atmosphe-
re.
Remove the upper part of the packaging and visually check
that the machine and its components are perfectly intact.
Then remove the packaging and proceed to carefully clean
the machine in order to remove any protective oils used for
transport.
- Assemble the legs (Fig. C1 pos.1) on the work surface, and
the extension device (Fig.C2 pos.2), taking care to ensure
that the leg with the switch housing is assembled as shown
in Fig.A, inserting and fixing only the screws closest to the
edges of the table with the nuts, then you will later have to
assemble the supports for the adjustable square.
- Position the on and off device
(Fig.C3 pos.1) close to the leg (Fig.C3 pos.3) and fix it well
using 2 screws 4.2x12.5 (Fig.C3 pos.2).
- Assemble the long arms (Fig.C4 pos.1) to the legs using
M6x16 screws and washers, then fix the short arms to each
other as shown in Fig.C5.
- Assemble the supports (Fig.C6-C7 pos.1) to the extension
device (Fig.C7 pos.2) and to the arms (Fig.C6 pos.2) using
the screws, washers and nuts.
N.B. The extension device can be assembled both on the
short side, and on the long side of the work surface, using
the supports.
- Assemble the supports for the adjustable square (Fig.C8
pos.1), with the shortest tongue facing upwards, one on the
right side of the starting device and one on the short side
close to the device, using the special screws, washers and
nuts. For fixing these supports use the 6x20mm screws.
- Take care to check that all the nuts and screws for fixing
the legs, the short arms and the extension device are well
fixed.
- Now assemble the plugs (Fig.C9 pos.1).
- Put the attachment for the dust device (Fig.C10 pos.1) in the
body (Fig.C10 pos.2) and fix everything using 4 screws.
- Turn over the assembled structure.
- Assemble the protractor and relative guide as shown in Fig.
C11 and C12.
- Assemble the handles for lifting the saw bench as shown in
Fig. C13 and C14.
- Attach the wheels to the legs (Fig.C15): connect the devices
(Fig.C16) to the legs, using 2 screws, washers and nuts for
each.
- Insert 2 seeger rings (Fig.C16 pos.2) in the rod (Fig. C16
pos.3) and place it in the special holes in the brackets (Fig.
C16 pos.1). Now insert the wheels and other 2 seeger rings
(one each side).
- Check that the screws and nuts of the brackets are well fixed
to the legs.
- Connect the pipe (Fig.C17 pos.1) from the blade protection
to the dust device.
- Connect the extraction fan connection to a good sawdust
extractor.
- Assemble the pipe holding device (Fig.C18 pos.1) using 2
screws, washers and nuts.
- Using the crank (Fig.A pos.7) raise the blade to the highest
position.
- Check that the distance between the blade teeth (fig.C19
pos.1) and the dividing blade (fig.C19 pos.2) is as illustrated
in fig. C19.
- Check that the vertical distance between the point of the
dividing blade and the top of the blade teeth is as illustrated
in Fig. C19.
- Check that the blade teeth are not touching the protection.
If necessary, carry out the adjustment according to the
Adjustments chapter.
IMPORTANT! Before starting the machine, make sure that
the protection devices are in perfect order, correctly adju-
sted and that the blade is well secured.
Plug the machine into the power outlet.
To start: press the green button with the (I) symbol;
To turn off: press the red button with the (O) symbol.
The switch is fitted with a minimum voltage device, which
automatically turns the switch itself "OFF" in the event of
a power cut, thus preventing accidental start-up when the
electricity is restored. In these cases, to restart the machine,
it is necessary to press the green button again after the power
supply voltage has been restored.
We recommend repeating these operations several times
before starting work, in order to familiarise yourself with the
controls.
ADJUSTMENTS
IMPORTANT! Before any adjustments, unplug the machine
from the power supply.
CUTTING DEPTH
To raise or lower the blade compared to the work surface, turn
the crank (Fig.A pos. 7).
To raise it: turn it clockwise.
To lower it: turn it anti-clockwise.
BLADE SLOPE (Fig. E)
For carrying out cuts on a slope of up to 45° compared to
the work surface:
loosen the knob (1) and adjust the blade to the required slope,
observing the scale (3); fix the knob well (1).
The screw with nut (2) must be tightened but must be able to
turn 'idle' so as not to prevent movement.
13
STARTING
