Idiomas disponibles
Idiomas disponibles
CHARACTERISTICS
- Possibility to cut on a slope.
- Adjustable cut depth.
- Upper and lower suction connection.
- Possibility of movement through the wheels.
EQUIPMENT
The packaging includes the following items:
- Saw bench.
- Blade
- Blade protection.
- Parallel guide.
- Adjustable piece guiding square.
- Piece pusher.
- Bolts and screws
- Operator's use and maintenance manual (this manual)
- Warranty (enclosed herewith)
- Conformity certificate (attached to this manual)
TECHNICAL DATA
Voltage and nominal frequency
Absorbed nominal power
Type of service
Nominal revolutions
Cutting blade diameter
Blade hole diameter
Cut thickness
Max. cut depth
Acoustic pressure
Acoustic power
GENERAL SAFETY REGULATIONS
1) It is prohibited for children and unskilled personnel to use
the machine.
2) Always check the efficiency and integrity of the machine;
it can cause serious injury to the person using it.
3) Keep a safe distance from property, people and ani-
mals and do not allow them to approach while you are
working.
4) Do not use the machine in closed or poorly ventilated
areas or in the presence of flammable and/or explosive
liquids, powders, gases or anything else of this kind.
5) Use a tool of suitable power for the job to be performed,
avoiding useless overloads, which could be hazardous for
the person using it and could also wear the tool early.
6) Never remove any machine components and do not
modify it in any way.
7) Never hold the machine by the cutting tool.
8) Always check that the blade is correctly fixed before using
the machine.
9) Make sure that any service keys have been removed
before using the machine.
10) The operator is responsible for third parties in the work
area.
11) Tie long hair back and do not wear bracelets or long ne-
cklaces as they could get caught up in the moving parts
of the machine.
12) Always wear appropriate clothing while working. Use
goggles and protective gloves. Normal glasses are not a
substitute for protective goggles. If dust is produced whilst
you are working, use the appropriate protection masks.
230 V~50Hz
2000W
S6 20% 5min
n0 2800min-1
315mm
30mm
2.5mm
60mm
LpA 82.9 dB(A)
LwA 93.67 dB(A)
12
IMPORTANT! Individual protective equipment is essential to
safeguard your own safety and health. Failure to observe
this regulation may cause serious problems with regard to
your physical integrity.
13) Never touch the moving parts of the machine.
14) Switch off the motor and disconnect the machine from
the power supply socket when: it is out of use, when
left unattended, when checking it, when the power cable
is damaged, when replacing the blade, when it is being
transported and when cleaning it.
15) Always keep the work area clean and free from ob-
stacles.
16) Never become distracted from what you are doing while
working.
17) Only work during daylight hours or with sufficient artificial
lighting.
18) Ensure that the switch is in the OFF position before plug-
ging it into the mains socket.
19) Only and always use the switch to stop the machine.
20) Only use this machine in the way described in these
instructions.
21) When not in use, keep the machine in a dry place out of
reach of children.
22) Periodically check that all screws are tight.
23) Always connect the machine to a dust extraction sy-
stem.
24) Periodically ensure that the ventilation grids of the motor
are perfectly clean and open.
25) HARMFUL DUST
IMPORTANT! The dust produced by some types of wood
are very harmful to your health. Wear appropriate masks,
extract the saw dust from the machine and equip the room
with an extractor for air exchange.
ELECTRICAL SAFETY REGULATIONS
1) The power supply voltage must correspond to that indi-
cated on the technical data plate. Do not use any other
type of power supply.
2) It is advisable to install a trip switch on the electrical power
supply line. Consult your electrician.
3) Do not use the machine on damp or wet surfaces or leave
it in the rain.
4) The power supply cable must be checked on a regular
basis and before each use of the tool to check if it is
damaged or worn. If it is seen to be in poor condition, do
not use the machine but have the cable repaired by an
authorised service centre.
5) If you use an extension cable with a reel, completely unreel
the cable, otherwise it could overheat and cause a fire.
6) If you are using an extension cable, make sure that it is
of a certified type. Keep it away from the work area, from
damp, wet, greasy and sharp surfaces and also from
sources of heat and combustibles.
7) The power socket must be bi-polar and earthed (10-
16A/250V). The cross section of the wire must be equal
to or greater than 1mm². Use a matched cable no lighter
than the H05VV-F type.
8) When unplugging the power supply cable from the socket,
always grip it by the plug.
STARTING UP (FIG. A-C)
IMPORTANT! The Manufacturer declines all responsibility
for any direct and/or indirect damage caused by incorrect
installation or connections.
