Replacing The Cutting Line; Disposal And Recycling - EINHELL AGILLO 36/255 BL Manual De Instrucciones

cover.
2. Take out the empty line spool and the
pressure spring.
3. Fig. 29 Thread the end of the line on the new
line spool through the eyelet in the spool
cover and allow approx. 5.1" (13 cm) of line to
project. Insert the pressure spring (32) in the
line spool.
4. Press the spool cover back into the line spool
housing.

7.3 Replacing the cutting line

Danger! Remove the battery packs!
1. Fig. 28 Press the line spool housing together
at the marked points and remove the spool
cover.
2. Take out the empty line spool and the
pressure spring.
3. Remove any remaining cutting line if there is
any.
4. Fig. 30 Insert the new cutting line through the
line mount inside the spool.
5. Wind the line with tension in a counter-
clockwise direction.
6. Fig. 31 Hook the line, approx. 5.9" (15 cm)
before the end of the line, into one of the line
holders on the edge of the spool.
7. Fig. 29 Thread the end of the line on the new
line spool through the eyelet in the spool
cover. Insert the pressure spring (32) in the
line spool.
8. Pull the line sharply to release it from the line
holder.
9. Press the spool cover back into the line spool
housing.
When you start the equipment again the line will
be cut to the perfect length automatically.
Caution! Bits of the nylon line could cause
injury when fl ung out.
7.4 Sharpening the guard hood blade
The guard hood blade (Fig. 2/Item 14) can
become blunt over time. When you notice this,
undo the screw holding the guard hood blade
on the guard hood. Clamp the blade in a vise.
Sharpen the blade with a fl at fi le and make sure
that the angle of the cutting edge is not altered in
the process. File in one direction only.
7.5 Maintenance
There are no other parts inside the equipment
which require maintenance.
Anl_Agillo_36_255_BL_SPK7_USA.indb 20 Anl_Agillo_36_255_BL_SPK7_USA.indb 20
EN
Spare line spool Art. No.: 3405097
Spare cutting blade Art. No.: 3405084

8. Disposal and recycling

The equipment is supplied in packaging to
prevent it from being damaged in transit. The
raw materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
9. Storage
Store the equipment and its accessories out
of children's reach in a dark and dry place at
above freezing temperature. The ideal storage
temperature is between 50°F and 104°F (10°C
and 40°C). Keep the electric tool in its original
packaging.
The equipment has an integrated wall holder (Fig.
32/Item 33) to enable it to be hung on the wall.
•
Always hold the equipment with one hand
on the handle and the other hand on the
additional handle. Do not carry the equipment
by its motor housing.
•
Secure the equipment against slipping if you
transport it in a vehicle.
•
As far as possible, use the original packaging
for transporting the equipment.
•
Use a transport guard for metal blades during
transport and storage.
The reprinting or reproduction by any other
means, in whole or in part, of documentation
and papers accompanying the products is
strictly subject to the express consent of Einhell
Germany AG.
Subject to technical changes.
- 20 -
07.12.2023 14:06:06 07.12.2023 14:06:06