Makita UM110D Manual De Instrucciones página 16

ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
When replacing the shear blades,
always wear gloves and attach the blade cover so
that your hands and face do not directly contact
the blades.
NOTICE:
When replacing the shear blades, do
not wipe off grease from the gear and crank.
Installing or removing the blade
cover for grass shear
CAUTION:
Be careful not to touch the blades
when installing or removing the blade cover.
To remove the blade cover, pull it slightly, and then slide
it sideways. To install the blade cover, perform the steps
in reverse.
► Fig.6
Installing or removing the grass
receiver
Optional accessory
CAUTION:
When installing or removing the
grass receiver, be sure to attach the blade cover
and be careful not to trap your fingers between
the tool and grass receiver.
Installing the grass receiver
1. Hook the hinge of the grass receiver on the groove
of the tool.
► Fig.7: 1. Hinge 2. Grass receiver
2. Align the protrusions on the grass receiver with
the grooves on the tool by sliding the grass receiver
toward the front of the tool and moving it in the direction
of the arrow.
► Fig.8
NOTICE:
Do not attach the hinge of the grass
receiver to the tool forcibly after aligning the pro-
trusions on the grass receiver with the grooves
on the tool.
Removing the grass receiver
1. Release the protrusions on the grass receiver
from the grooves on the tool while sliding the grass
receiver toward the front of the tool.
► Fig.9: 1. Grass receiver
2. Release the hinge of the grass receiver from the
tool.
Installing or removing the shear
blades for grass shear
NOTICE:
If the parts other than the shear blades
such as the crank are worn out, ask Makita
Authorized Service Centers for parts replacement
or repairs.
Removing the shear blades
1. Remove the grass receiver if it's installed. Place
the tool upside down.
► Fig.10
2. While pressing the lock lever, turn the undercover
counterclockwise until
with on the lock lever.
► Fig.11: 1. Undercover 2. Lock lever
3. Remove the undercover, shear blades, and crank.
► Fig.12: 1. Undercover 2. Grass shear blades
3. Crank
Installing the grass shear blades
1. Prepare the crank, undercover, and new grass
shear blades.
► Fig.13: 1. Crank 2. Undercover 3. Grass shear blades
2. Remove the blade cover from the old grass shear
blades, and then attach it to the new ones.
► Fig.14: 1. Blade cover
3. Adjust the three pins so that they are lined up on
the alignment line.
► Fig.15: 1. Alignment line
4. Apply a small amount of grease to the periphery
of the crank. Attach the crank to the pins with the small
and large rounds facing up.
► Fig.16: 1. Crank
5. Adjust the blades and guide plate so that the hole
in the guide plate and the two protrusions on the blades
are lined up.
► Fig.17: 1. Guide plate
6. Turn the shear blades upside down and install
them so that the pins on the tool fit in the hole on the
guide plate. Make sure that the shear blades are fixed
securely in place.
► Fig.18: 1. Guide plate
NOTE: Sliding the blade cover forward slightly makes
it easier to install the shear blades.
7. Place the undercover so that
cover is aligned with
► Fig.19: 1. Undercover 2. Lock lever
8. While pressing the undercover, turn the under-
cover clockwise until
with on the lock lever.
► Fig.20: 1. Undercover 2. Lock lever
9.
Make sure that the lock lever fits in the groove on
the undercover.
► Fig.21: 1. Lock lever
16 ENGLISH
on the undercover is aligned
on the under-
on the lock lever.
on the undercover is aligned