Idiomas disponibles
Idiomas disponibles
English
defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead‑based paints,
• crystalline silica from bricks and cement and other masonry
products, and
• arsenic and chromium from chemically‑treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well‑ventilated area, and work
with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
• Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or
lie on the skin may promote absorption of harmful chemicals.
Direct particles away from face and body.
• Use the appropriate dust extractor vacuum to remove
the vast majority of static and airborne dust. Failure
to remove static and airborne dust could contaminate the
working environment or pose an increased health risk to the
operator and those in close proximity.
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be caught in
moving parts.
CAUTION: When not in use, place tool on its side
on a stable surface where it will not cause a tripping
or falling hazard. Some tools with large battery packs
will stand upright on the battery pack but may be easily
knocked over.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
BPM .................... beats per minute
V ......................... volts
min ..................... minutes
j
or DC ............ direct current
.../min .............. per minute
RPM .................... revolutions per
minute
A ......................... amperes
Hz ....................... hertz
W ........................ watts
Wh ...................... watt hours
n o ....................... no load speed
n ......................... rated speed
c
..................... safety alert symbol
SPM .................... strokes per minute
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start‑up can
cause injury.
Blade Installation and Removal (Fig. B)
WARNING: Cut hazard. Blade breakage may occur if the
blade does not extend past the shoe and the thickness of the
workpiece during the cut. Increased risk of personal injury, as
well as damage to the shoe and workpiece may result.
6
h
..................... wear respiratory
protection
f
..................... wear eye
protection
i
..................... Class II
Construction
(double insulated)
g
..................... wear hearing
protection
a
..................... read all
documentation
n
..................... avoid staring at
light
l
or AC............ alternating current
Ah ....................... amp hours
To Install a Blade
1. Point tool away from body.
2. Pull the blade clamp lever
open to its full open position.
3. Insert blade
fully into blade clamp collar.
10
nOTE: Blade can be installed with the teeth facing up to
assist in Flush Cutting.
4. Release blade clamp lever
to ensure blade is clamped securely.
To Remove a Blade
WARNING: Burn hazard. Do not touch the blade
immediately after use. Contact with the blade may result in
personal injury.
1. Pull the blade clamp lever
open to its full open position.
2. Remove blade.
To Remove a Broken Blade
If the blade breaks so that the broken piece is caught
inside the clamp, take the following steps to remove the
remainder of the blade from the saw.
1. Place the saw on its side on a flat stable surface with the
blade clamp collar tab pointing up.
2. Pull the blade clamp lever
clamp collar to its full open position.
a. if the blade has broken inside the clamp, slide a flat
object into the opening of the clamp as far as it can go, then
remove the flat object. This will disengage the pin inside
the clamp.
b. if the blade has broken outside the clamp, slide a flat
object into the opening of the clamp to the left of the blade
as far as it can go, then remove the flat object. This will
disengage the pin inside the blade clamp collar.
3. Hold the blade clamp collar open with the saw on its side
or with the shoe end pointed downward. While holding blade
clamp lever open all the way, shake the saw until the broken
blade falls out of the blade clamp collar.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start‑up can
cause injury.
Installing and Removing the Battery Pack (Fig. C)
WARNING: Ensure the tool/appliance is in the off position
before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle and
slide it into the handle until the battery pack is firmly seated
in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
battery pack release button
pack out of the tool handle. Insert it into the charger.
Proper Hand Position (Fig. D)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
3
upwards; the collar will
3
and gently tug on the blade
upwards; the collar will
3
upwards to open the blade
3
into the tool handle, align
6
and firmly pull the battery
7
