Triton TPT 125 Instrucciones De Uso Y De Seguridad página 6

- Inspect extension cables periodically and replace if damaged
- Keep handles dry, clean and free from oil and grease
WARNING: Many accidents are caused by poorly maintained
power tools.
15 Disconnect tools - When not in use, before servicing and
when changing accessories such as blades, bits and cutters,
disconnect tools from the power supply
WARNING: The use of accessories or attachments not
recommended by the manufacturer may result in a risk of injury
to persons.
16 Remove adjusting keys and wrenches - Form the habit of
checking to see that keys and adjusting wrenches are removed
from the tool before switching it 'ON'
17 Avoid unintentional starting - Ensure switch is in 'O' position
when connecting to a mains socket or inserting a battery pack,
or when picking up or carrying the tool
WARNING: Unintended starting of a tool can cause major
injuries.
18 Use outdoor extension leads - When the tool is used
outdoors, use only extension cords intended for outdoor use
and so marked. Use of an extension cable suitable for outdoor
use reduces the risk of electric shock
19 Stay alert
- Watch what you are doing, use common sense and do not
operate the tool when you are tired
- Do not use a power tool while you are under the influence of
drugs, alcohol or medication
WARNING: A moment of inattention while operating power
tools may result in serious personal injury.
20 Check damaged parts
- Before further use of tool, it should be carefully checked
to determine that it will operate properly and perform its
intended function
- Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting and any other conditions
that may affect its operation
- A guard or other part that is damaged should be properly
repaired or replaced by an authorized service centre unless
otherwise indicated in this instruction manual
- Have defective switches replaced by an authorized service
centre
WARNING: Do not use the tool if the ON/OFF switch does not
turn it 'ON' and 'OFF' . The switch must be repaired before the tool
is used.
21 Use recommended accessories - Consult the owner's manual
for recommended accessories
EN WARNING: The use of any accessory or attachment other than
one recommended in this instruction manual may present a risk of
personal injury.
22 Have your tool repaired by a qualified person - This electric
tool complies with the relevant safety rules. Repairs should
only be carried out by qualified persons, otherwise this may
result in considerable danger to the user
WARNING: When servicing use only identical replacement
parts.
6
WARNING: If the power cable is damaged it must be replaced
by the manufacturer or an authorised service centre.
23 Power tool mains plugs must match the mains socket -
Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs
and matching sockets will reduce risk of electric shock
24 If operating a power tool outside use a residual current
device (RCD) - Use of an RCD reduces the risk of electric shock
25 When used in the United States, Australia or New Zealand,
it is recommended that this tool is ALWAYS supplied
via Residual Current Device (RCD) with a rated residual
current of 30mA or less
26 Use proper extension cord. Make sure your extension cord
is in good condition. When using an extension cord, be
sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. Table
A shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier the cord
27 Never leave the tool running unattended. Turn power off.
Don't leave the tool until it comes to a complete stop
Even when used as prescribed it is not possible to eliminate all
residual risk factors. Use with caution. If you are at all unsure of the
correct and safe manner in which to use this tool, do not attempt
to use it.
WARNING: Before connecting a tool to a power source (mains
switch power point receptacle, outlet, etc.) be sure that the voltage
supply is the same as that specified on the nameplate of the tool. A
power source with a voltage greater than that specified for the tool
can result in serious injury to the user, and damage to the tool. If in
doubt, do not plug in the tool. Using a power source with a voltage
less than the nameplate rating is harmful to the motor.
Table A
Ampere Rating Volts
120
240
More Not
than more
than
0 6
6 10
10 12
12
16
Total length of cord in metres
7.5 15 30.5 46
15 30.5 61 92
Minimum gauge for cord
18 16 16 14
18 16 14 12
16 16 14 12
14
12
Not
recommended