Idiomas disponibles
Idiomas disponibles
Maximum number of
Simplebus1 audio internal units
Maximum number of
Simplebus2 video internal
units
Ethernet connection
distance with 1440, IN port
Ethernet connection
distance with 1440, OUT port
Ethernet port
Operating temperature (°C)
Operating humidity (max. RH) 95%
Dimensions
PROGRAMMING VIA VIP MANAGER
All art. 1469 configurations can be implemented via
PC and ViP Manager configuration software, which
is available to download free of charge from the
website pro.comelitgroup.com
When connecting the PC to the ViP
network via art. 1440, use the red
Comelit cable art. 1449.
REBOOT WITH PREDETERMINED NETWORK
SETTINGS
This procedure is used to restart the module with the
default network parameters.
In the event of a further restart the module:
•
will restore the parameters from the previous
configuration, if the user has not made any
changes;
•
will start up with the new network parameters,
if the parameters have been changed using ViP
Manager.
f DIP-switches set to OFF
1. Cut off the device power supply
2. Set DIP 1 to ON
3. Restore the device power supply
4. Wait for approximately 20-40 sec., until the LEDs
flash slowly and alternately (1 sec. red / 1 sec.
green)
5. Set DIP1 back to OFF
»
The green LED will flash for 5 sec.
»
The device will start with the default network
settings.
•
The saved parameters will be recovered at a
subsequent device restart process.
RESTORE FACTORY SETTINGS
100
This procedure is used to restore all the parameter
values to their factory settings, and to clear all
100
device configurations.
f DIP-switches set to OFF
100 m
1. Cut off the device power supply
2. Set all DIP-switches to ON
150 m
3. Restore the device power supply
10/100 Mbps
4. Wait for approximately 20-40 sec., until the LEDs
-5 to +50
90x70x59 mm
5. Set the DIP-switches back to OFF
(4 DIN modules)
»
»
WIRING DIAGRAMS
WARNING
• This Comelit product is designed and manufactured for use in the creation
• All activities connected to the installation of Comelit products must be
• Disconnect the power supply before carrying out any operations on the
• Use wires with a cross-section suited to the distances involved, observing
• We advise against running the system wires through the same duct as
• To ensure Comelit products are used safely: carefully observe the
• Comelit products do not require maintenance aside from routine cleaning,
• Comelit Group S.p.A. accepts no liability for any purpose other than the
• The manufacturer, Comelit Group S.p.A., hereby declares that this
•
4
flash rapidly and alternately (0.1 sec. red / 0.1
sec. green)
The red LED will flash for 5 sec.
The device will restart.
page 15-16
of audio and video communication systems in residential, commercial,
industrial and public buildings.
carried out by qualified technical personnel, with careful observation of
the indications provided in the manuals / instruction sheets supplied with
those products. The product must be installed to the highest standards.
wiring.
the instructions provided in the system manual.
power cables (230V or higher).
indications provided in the manuals / instruction sheets; make sure the
system created using Comelit products has not been tampered with /
damaged.
which should be carried out in accordance with the indications provided
in the Manuals / Instruction sheets. Any repairs must be carried out:
for the products themselves, exclusively by Comelit Group S.p.A., for
the systems, by qualified technical personnel. Do not use alcohol or
aggressive products for cleaning purposes.
intended use, or failure to observe the indications and warnings contained
in this manual / instruction sheet. Comelit Group S.p.A. reserves the right
to change the information provided in this manual / instruction sheet at
any time and without prior notice.
equipment conforms to the applicable directives. The full EU conformity
declaration is available on the web page for the product.
In accordance with art. 26 of Italian Legislative Decree dated
14th March 2014, no. 49 "Implementation of directive
2012/19/EU on Waste Electrical and Electronic Equipment
(WEEE)", the "crossed-out wheelie bin" symbol indicates that
at the end of its useful life, this product must be separated from other
waste before collection for disposal. The user should therefore take the
exhausted appliance to suitable local collection centres for waste
electrical and electronic products. As an alternative to handling this
process yourself, you can take the appliance to your local equipment
dealer when purchasing a new equivalent product. Electronics dealership
businesses covering an area of 400 m² are also obliged to accept waste
electronic products smaller than 25 cm for disposal, without any
obligation to purchase. Suitable separated waste collection for the
subsequent reuse of the appliance sent for recycling, processing and
environmentally conscious disposal helps to avoid potential negative
effects on the environment and human health, and encourages the reuse
and recycling of the materials used in the construction of the appliance.
