NAD 616 Manual Del Usuario página 4

GB
INSTALLATION
The recorder may be installed on any stable sur-
face that is not subjected to vibration or intense mag-
netic fields. It should not be placed directly on a loud-
speaker, a television set, or a large power amplifier
where it might pick up hum from the amplifier's power
transformer. If you wish to install the recorder next to
an amplifier on the same shelf, place the recorder on
the right so that its cassette compartment will be
located away from the amplifier.
Allow adequate ventilation. Do not place this prod-
uct on a soft surface such as a carpet or in an
enclosed position such as a book case or cabinet that
may impede the airflow through the ventilation slots.
WARNING TO UK USERS. If this appartus is not fit-
ted with a UK three-pin plug, do not attempt to insert
the attached plug into a UK mains socket. Instead, cut
the plug from the mains lead and attach a fused UK
three-pin plug using the following safety advice on
wiring.
IMPORTANT. The wires in this mains lead are
coloured BLUE and BROWN;
BLUE: NEUTRAL
The colours of these mains lead wires may not corre-
spond with the coloured markings identifying the ter-
minals in your plug. In this case the BROWN wire
must be connected to the terminal which is marked
L(ive) or coloured RED. The BLUE wire must be con-
nected to the terminal marked N(eutral) or coloured
BLACK. No connection should be made to the termi-
nal marked E or coloured green or green and yellow
WARNING: BEFORE PLUGGING IN THE UNIT FOR
THE FIRST TIME, READ THE FOLLOWING SEC-
TION CAREFULLY.
Some models are designed for use only with the
power supply voltage of the region where they are
sold.
European and Australian models: AC 230V, 50Hz.
U.S.A. and Canadian models: AC 120V, 60Hz.
PRECAUTIONS
To ensure that maximum performance of the NAD
616 cassette deck is maintained over time, please
bear the following precautions in mind:
THE DECK
A. Make sure the heads and transport are cleaned
regularly. Please refer to chapter "Maintenance".
B. Demagnetise heads and tape guidance of both
tape transports from time to time. Please refer to
chapter "Maintenance".
C. The bearings and other moving parts have been
treated with special lubricants and are therefore main-
tenance-free. Additional lubrication can actually cause
malfunctioning.
D. Do not position the deck near equipment with
strong magnetic fields, such as loudspeakers or tele-
visions, etc.
E. Place the deck on a solid, flat surface.
F. Avoid dirt, dust, sand, etc. from entering the deck.
NAD
4
NAD 616 CASSETTE DECK
G. Avoid placing near transmitters: they can generate
high frequencies which may cause malfunctioning of
the deck.
H. Ensure the cassette deck compartment lids are
closed when the deck is not in use. Open the cassette
compartments only for taking a cassette in or out, or
for cleaning the heads and tape guides.
I. Do not place the deck directly on top of a (power)
amplifier or receiver. The deck may pick up hum from
the amplifier's power transformer. Some amplifiers
can also generate a fair amount of heat, even when
on stand-by.
THE CASSETTE TAPES
A. Store the cassette tapes in their jewel case, away
from dust. Never store tapes in direct sunlight or very
hot places.
B. Always use cassette tapes of a good quality.
Besides mediocre results, poor quality tapes can
cause excessive head wear.
C. Never touch the exposed tape itself or take it out
of its cassette casing.
BROWN: LIVE
D. In most cases the cassette tape has a five to eight
second leader tape at both the beginning and end of
a cassette tape. As you cannot record on this leader
tape, be sure to commence recording beyond this
tape.
NOTE: C-120 tapes and endless tapes are not rec-
ommended because of their fragile nature.
REAR PANEL CONNECTIONS
& CONTROLS The numbers in the text refer to the connections in
figure "REAR PANEL CONNECTIONS"
This cassette deck can be connected to almost all
pre-amplifiers, integrated amplifiers or receivers.
Ensure the plugs are fully inserted and the recording
and playback cables are connected properly.
1. LINE IN.
Connect a cable from the deck's "LINE IN" jacks at
the rear panel to the TAPE OUT or REC (OUT) jacks
of your amplifier. Connect the left channel of the deck
to the left channel of the amplifier and connect the
right channel of the deck to the right channel of the
amplifier. Normally, the red plug is used for the right
channel, the black or white plug for the left channel.
Please refer to figure 1.
2. LINE OUT.
Connect a cable from the deck's "LINE OUT" jacks
at the rear panel to the TAPE IN, PLAY, or MONITOR
jacks of your amplifier. Connect the left channel of the
deck to the left channel of the amplifier and connect
the right channel of the deck to the right channel of
the amplifier. Normally, the red plug is used for the
right channel, the black or white plug for the left chan-
nel. Please refer to figure 1.