Kaco blueplanet 29.0TL3 S Manual De Instrucciones página 45

Manual
Country- Me- Display/
spec. Set- nu Setting
tings level
Not for IL, P(f) Modo de servicio
1 2 3 4 4
IT
Off | Mode 1 | Mo-
de 2
Umbral de activa.
1 2 4 4
3
45 Hz – 70 Hz
Umbral de desactiv.
1 2 3 4 4
Min. 45 Hz – 61,5 Hz
Max. 45 Hz – 70 Hz
Not for IL, Tiempo de desactiv.
1 2 3 4 4
IT
0 – 3600 [s] /
[s] / 1
Gradiente
1 2 3 4 4
40 [% Hz] /
Hz] 1 [% Hz]
Retardo intencionado
1 2 4 4
3
0.00 – 5.00 [s] / [s] / 0.01
Settling time
1 2 3 4 4
0 – 2000 [ms] /
[ms] /
Rise Outg. grad. & Fall.
4 4
1 2 3
Outg. grad.
1 – 60000 [%/Min] /
60000 [%/min] /
Deact. grad.
4
1 2 3 4
1 – 60000 [%/Min] /
10 [%/Min] /
Fault Ride Through
1 2 3 4 4
Potencia reactiva
1 2 3 4 4
Especific. cos-phi
1 2 3 4 4
0,3 – 1 /
0,001
Over-excited | un-
der-excited
Kaco blueplanet 29.0TL3
Action in this menu/meaning
AVISO: More detailed information can be found in
F Specify the operation mode.
F Specify activation threshold (if mode 1 or mode 2 is active, this menu
option is displayed permanently for IT and IL!)
AVISO: The function is activated if the activation threshold is
exceeded. In mode 2 this value also serves as a deactivation
threshold.
AVISO: If the grid frequency is within the deactivation range
for the duration of the deactivation time, then the function is
deactivated.
F Specify deactivation threshold (if mode 1 or mode 2 is active, this
menu option is displayed permanently for IT and IL!).
F Specify time for power reduction (if mode 1 is active)
2
F Set gradient of power limitation function with increasing frequency.
The percentage value is based on the rated frequency (if mode 1 or
40 [%
mode 2 is active, this menu option is displayed permanently for IT
and IL!)
F Set the power limitation delay (if mode 1 or mode 2 is active; this
menu option is displayed permanently for IT and IL!).
0
F Set the power reduction delay in seconds (if mode 1 or mode 2 is ac-
tive; this menu option is displayed permanently for IT and IL!).
0
1 [ms]
F Specify the increasing and decreasing output gradient.
1
F Specify deactivation gradient (if mode "1" or mode "2" is active. This
menu option is displayed permanently for IT and IL!).
1
AVISO: The device supports dynamic grid stabilization (Fault
Ride-Through).
F Further parameterisation is possible via the web interface
1. Open the menu: Press the Right arrow button or Enter
button.
2. Activating reactive power process: Select process a press the En-
ter button. The active process is highlighted.
More detailed information about the procedure can be found at:
1,000 / 1. [Ver capítulo 10.1} Página 59]
2. Determine the specified power factor.
F If a power factor not equal to 1 is selected: Select the type of phase
shift: under-excited (inductive load), over-excited (capacitive load).
Configuration and operation | 9
Página 45