Metabo WPB 36 LTX BL 230 Manual Original página 11

Avoid the machine swirling up or taking in dust
and chips. After switching off the machine,
only place it down when the motor has come to a
standstill.
See illustration B on page 2.
Torque activation:
Switching on: Slide the lock (13) in the direction of
the arrow and press the trigger switch (14).
Switching off: Release the trigger switch (14).
7.1 Working Directions
Grinding:
Press down the machine evenly on the surface and
move back and forth so that the surface of the
workpiece does not become too hot.
Rough grinding: position the machine at an angle of
30° - 40° for the best working results.
Cut-off grinding:
Always work against the run of the disc
(see illustration). Otherwise there is
the danger of the machine kicking
back from the cut out of control. Guide
the machine evenly at a speed
suitable for the material being processed. Do not tilt,
apply excessive force or sway from side to side.
Sanding:
Press down the machine evenly on the surface and
move back and forth so that the surface of the
workpiece does not become too hot.
Wire brushing:
Press down the machine evenly.
8. Cleaning
Button (16) for adjusting the handle:
Occasionally vacuum clean the button or blow
compressed air through it (when pressed, in all 3
main handle positions). Prior to this operation,
separate the power tool from the power source and
wear protective goggles and a dust mask.
9. Transport
Transport of li-ion battery packs:
The shipping of li-ion battery pack is subject to laws
related to the carriage of hazardous goods (UN
3480 and UN 3481). Inform yourself of the currently
valid specifications when shipping li-ion battery
packs. If necessary, consult your freight forwarder.
Certified packaging is available from Metabo.
Only send the battery pack if the housing is intact
and no fluid is leaking. Remove the battery pack
from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with
adhesive tape).
Remove the battery pack from the machine to
transport the machine.
10. Troubleshooting
The electronic signal indicator (4) lights up and
the load speed decreases. The temperature is too
high! Run the machine in idling until the electronic
signal indicator switches off.
The electronic signal display (4) flashes and
the machine does not start. The restart protection
is active. The machine will not start if the battery
pack is inserted while the machine is on. Switch the
machine off and on again.
The electronic signal display (4) flashes and
the machine does not start. Press the button (5);
the LEDs the charge level. When the battery pack is
empty it must be recharged.
Electronic safety stop: The electronic signal
display (4) flashes and the machine was
SWITCHED OFF automatically. If the slew rate of
the current is too high (for example, if the machine
suddenly seizes or kickback occurs), the machine
switches off. Switch off the machine. Switch it on
again and continue to work as normal. Try to
prevent the machine from seizing. See chapter 3.2.
11. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Fit accessories securely. If the machine is operated
in a holder: secure the machine well. Loss of control
can cause personal injury.
Always use the suitable accessory and the
prescribed guard for the matching guard for
the application. See page 5. (Illustrations are
examples).
Application:
1 = surface grinding
2 = cut-off grinding
3 = drilling of holes
4 = wire brushes
5 = grinding with sanding paper
Accessories:
1.1 = grinding wheel
1.2 = cup wheel (ceramic)
2.1 = cut-off wheel "metal"
2.2 = cut-off wheel "masonry/concrete"
2.3 = diamond cutting disc "masonry/concrete"
2.4 = dual-purpose diamond cutting discs
(combined grinding and cutting disc)
3.1 = diamond drill bits
4.1 = wheel brush
4.2 = cup brush
5.1 = flap disc
5.2 = backing pad for sanding sheets
prescribed guard:
Type A = cutting guard
Type B = guard for grinding
Type C = guard for grinding and cutting-off
operations (combination)
Type D = guard for cup wheel
ENGLISH en
11