Idiomas disponibles
Idiomas disponibles
m
WARNING
Excessive and frequent exposure to noise can lead to
hearing damage or hearing loss.
-
Wear hearing protection
-
Take breaks.
Total vibration values (vector sum of three directions)
determined according to EN 62841.
NOTE: The specified noise emission values have been
measured in accordance with a standardised test pro-
cedure and can be used to compare one power tool
with another.
The specified noise emission values can also be used
for an initial estimation of the exposure.
WARNING: The noise emission values can vary from
the specified values during the actual use of the power
tool, depending on the type and the manner in which
the power tool is used, and in particular the type of
workpiece being processed.
Implement measures to protect against noise nuisance.
In doing so, take into account the complete working
process, including the times when the power tool is
working without load or switched off. Suitable meas-
ures include regular maintenance and care of the pow-
er tool and the insertion tools, regular breaks as well as
proper planning of the working process.
8. Commissioning
m
ATTENTION!! Always disconnect the power supply
before beginning any maintenance or setup work on
the machine.
Mounting belt/disc sander to work bench
If your belt/disc sander is to be used in a permanent lo-
cation, it is recommended you secure it to a workbench
or other stable surface. When mounting the belt/disc
sander to a workbench, holes should be drilled through
the supporting surface of the workbench.
• Mark holes on workbench where belt/disc sander is
to be mounted using holes in the base as a template
for hole pattern.
• Drill holes through workbench.
• Place belt/disc sander on workbench aligning holes
in the base with holes drilled in the workbench.
• Insert bolts and tighten securely with lock washers
and hex nuts.
22 | GB
Clamping belt/disc sander to work bench
If your belt/disc sander is to be used as a portable
tool, it is recommended you fasten it permanently to a
mounting board that can easily be clamped to a work-
bench or other stable surface.
The mounting board should be of sufficient size to
avoid tipping while belt/disc sander is in use. Any good
grade plywood or chipboard with a 3/4 in. (19 mm)
thickness is recommended.
• Mark holes on board where belt/disc sander is to
be mounted.
• Follow last three steps in section Mounting Belt/
Disc Sander to Workbench.
Note! If lag bolts are used, make sure they are long
enough to go through holes in belt/disc sander base
and material the belt/ disc sander is being mounted
to. If machine bolts are used, make sure bolts are long
enough to go through holes in belt/disc sander, the
material being mounted to, and the lock washers and
hex nuts.
Connection to vacuum suction.
The use of an extraction system is recommended.
Tool changes, Fig. 2–7
m
ATTENTION!! Turn off the machine and disconnect
the main plug.
When changing tools make sure to have all parts
cleaned.
Prepare the appropriate tool and mount it as follows:
1.
Attach the lower spindle disc (11) to the spindle
(4) (fig. 2).
2.
Insert the table inlays (5) into the table (fig. 3).
3.
Slide the rubber sleeve (6) onto the spindle (4)
(fig. 4).
4.
Slide the abrasive sleeve (7) onto the rubber
sleeve (6) (fig. 5).
5.
Apply the disc (12) (use the correct measure-
ments) (fig. 6).
6.
Put on the hex-nut and tighten it with the hook
wrench (13). (fig. 7)
Be sure always to mount the correct parts when
changing the abrasive sleeves. The table inlays have
to be bigger than the abrasive sleeves. (fig. 8)
Note! The 13 mm abrasive sleeve is put directly onto
the spindle (4).
www.scheppach.com
