Idiomas disponibles
Idiomas disponibles
Anleitung_STR_920_L_SPK7:_
GB
8. RCD plug (Fig. 16)
Connect the RCD plug (41) to the power supply.
Press the reset button (42) and the control lamp (43)
will begin to shine. Press the test button (44) to
check the function of the RCD plug. If everything is
working properly the control lamp (43) will go out and
the contact to the power supply will be interrupted.
The RCD plug triggers at a fault current of 10 mA.
Defective RCD plugs must be replaced by a qualified
electrician.
Press the reset key (42) again in order to be able to
start up the machine.
9. Assembly and operation (Fig. 3/4/5)
9.1 Fitting the hose and cable guide (Fig. 17)
9.2 Assembly of the sub-frame and cooling water
pump (Fig. 2-4)
Secure the feet (1) to the water trough using the
thumb screws (12).
Place the complete tile cutter into the trough (3).
Place the cooling water pump (13) in a suitable
position in the water trough and secure it to the
base of the trough with the suction cups. The
pump, cable and cooling water hose (14) must
not be able to get into the cutting area.
Fill with water until the pump (13) is completely
immersed in water.
Remove the star handle screw (11) and spacer
(40).
Important: Before you lift the machine out of the
trough or transport it, the cutting unit must be
secured again with the star handle screw (11) and
spacer (40).
9.3 ON/OFF switch (Fig. 6)
To switch on, press the "1" on the ON/OFF
switch (16).
Before you begin cutting, wait until the cutting
wheel has reached maximum speed and the
cooling water pump (13) has started supplying
the cutting wheel with water.
To switch off, press the "0" on the switch (16).
Your machine is equipped with an overload
switch (16 a). If the machine is overloaded, the
overload switch (16 a) will trigger. After a cooling
down period, the machine can be reactivated by
pressing the overload switch (16 a).
18
07.02.2011
8:24 Uhr
Seite 18
9.4 90° Cutting (Fig. 7/8)
Loosen the star grip screw (27).
Set the angle stop (5) to 90° and retighten the
star grip screw (27).
Retighten the screws (28) to fasten the angle
stop (5).
Move the machine head (29) to the far end with
the handle (9).
Position the tile against the rail fence (6) on the
angle stop (5).
Switch on the tile cutting machine.
Caution: Always wait until the cooling water has
reached the cutting wheel (2) first.
Move the machine head (29) slowly and
smoothly forward through the tile with the handle
(9).
Switch off the tile cutting machine after
completion of cutting.
9.5 45° Diagonal cut (Fig. 9)
Set the angle stop (5) to 45°.
Cut as described in 9.4
9.6 45° Lengthwise cut, "jolly cut" (Fig.10)
Loosen the star grip screw (10).
Tilt the guide rail (7) to the left to 45° on the
angle scale (17).
Retighten the star grip screw (10).
Cut as described in 9.4.
9.7 Machining large workpieces (Fig. 11/12)
To enable you to machine large workpieces, the
cutting unit can be pivoted upwards. In this position
you can machine workpieces with a length of up to
920 mm (up to a max. workpiece thickness of 38
mm).
Remove the screw (37) on the top for this
purpose.
The cutting until will pivot upwards automatically.
You can now complete the required cuts as
described in sections 9.4 to 9.6. All that is
required is slight additional pressure downwards
on the handle.
9.8 Changing the diamond cutting wheel
(Fig. 13/14)
Pull out the power plug.
Unscrew the 3 screws (30) and remove the
safety hood (8) for the blade.
Place the wrench (31) on the motor shaft and
hold.
Using the wrench (34), loosen the flange nut in
the direction of rotation of the cutting wheel (2).
(Caution: Left-hand screw-thread.)
Remove the outer flange (35) and cutting wheel
(2).
