Idiomas disponibles
Idiomas disponibles
Settings
Settings on the robot
Cleaning can also be started from the cleaning robot
without an app. The following commands can be exe-
cuted using the buttons:
● Start cleaning via the On/Off/Pause button.
● Interrupt cleaning via the On/Off/Pause button.
● Return the cleaning robot manually to the charging
station via the Home button.
The cleaning robot automatically returns to the charging
station for recharging when it has completed a cleaning
task or when it is low on energy during a cleaning pro-
cess.
Settings in the app
The Kärcher Home Robots App offers the following
main functions, among others:
● Step-by-step guide for configuration options
● Map creation for rooms and several floors
● Setting of time schedules
● Definition of no-go zones and virtual walls
● Notes on faults or malfunctions and the cleaning
progress
● Setting of cleaning parameters such as amount of
water, cleaning intensity, number of passes or car-
pet avoidance mode
● Establishment of cleaning zones
● Activation/deactivation of the "Do not disturb" mode
● FAQ with detailed troubleshooting
Switching on the cleaning robot
Note
Place the cleaning robot directly on the charging station
if it cannot be switched on due to a too low charging
state, see chapter Initial start-up.
1. Place the cleaning robot manually on the charging
station and make sure that the battery terminals
have a good contact.
The cleaning robot switches on automatically and
emits an acoustic signal.
The LED display indicator "Robot status" pulses yel-
low.
Note
Alternatively, the cleaning robot can also be switched on
when it is not on the charging station:
2. Keep On/Off/Pause button pressed for 3 seconds.
The cleaning robot switches on.
Illustration E
Operation without app
Starting cleaning
Note
Open the doors to all rooms that the cleaning robot is to
clean and keep the floor free of objects lying around.
1. Press the On/Off/Pause button.
The cleaning robot gives a verbal signal and first
creates a map of the surroundings without cleaning.
The LED display indicator "Robot status" lights up
blue.
When the map creation is finished, it returns to the
charging station.
As soon as the cleaning robot is connected to the
charging station, the LED display indicator "Robot
status" lights up yellow and the LED display indica-
tor "Battery" pulses green.
Note
Wait a few seconds until you press the On/Off/Pause
button again so that the robot can save the map.
2. Press the On/Off/Pause button.
The cleaning robot gives a verbal signal and starts
cleaning.
The LED display indicator "Robot status" lights up
blue.
Operation with the app
Note
Open the doors to all rooms that the cleaning robot is to
clean and keep the floor free of objects lying around.
1. In the app, press the control panel "Start" and follow
the steps indicated as needed.
The cleaning robot gives a verbal signal and starts
the map creation.
The LED display indicator "Robot status" lights up
blue.
When the map creation is finished, it returns to the
charging station.
As soon as the cleaning robot is connected to the
charging station, the LED display indicator "Robot
status" lights up yellow and the LED display indica-
tor "Battery" pulses green.
Note
When the cleaning robot is connected to the charging
station, it takes a few seconds to create the map in the
app. The LED display indicator "Robot status" pulses
yellow.
After the map has been successfully saved, an acoustic
signal sounds.
Configuring the robot in the app
Individual configurations of the map can be made in the
app.
● Virtual walls and restricted areas prevent the clean-
ing robot from entering areas that should not be
cleaned.
● With spot cleaning or cleaning zones, the robot can
specifically clean the areas selected by the user
once.
● With different cleaning modes, the cleaning intensity
can be selected individually for each room depend-
ing on the type of floor or soiling (amount of water,
number of passes per area, different roller speeds
and robot travel speed, etc.)
Downloading the app is described in the chapter Con-
necting cleaning robots with WLAN and App.
1. Follow the step-by-step instructions in the App.
1. Select the desired map in the app and start cleaning
according to the individual configuration.
Interrupting cleaning
Interrupt cleaning on the device:
1
Press any button during cleaning.
The cleaning robot stops.
The LED display indicator "Robot status" pulses
blue.
2
Press the On/Off/Pause button.
Cleaning continues.
Interrupt cleaning in the app:
1. In the app, press the control panel "Start".
The cleaning robot stops.
The LED display indicator "Robot status" pulses
blue.
2. In the app, press the control panel "Start".
Cleaning continues.
English
Creating a map
Starting cleaning
21
