HIKOKI CS 3625DC Instrucciones De Manejo página 14

English
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate,
and the battery life will be shortened. Leave the battery
and recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because it
has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for
0.3 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
MOUNTING AND OPERATION
Action
Removing and inserting the battery
Switch operation*
1
Using the hook*
2
Selecting accessories
*1 Switch operation
When the switch is engaged while sliding the lock-off
lever, the saw chain rotates. (Fig. 7)
Unless the lock-off lever is being slid, the switch cannot
be engaged.
After the switch is engaged, the saw chain continues
rotating as long as it is pressed down.
When the switch is released, a brake is applied to stop
the saw chain rotation.
WARNING
Do not secure the lock-off lever in the slid position.
If the switch is accidentally engaged, the unit may
unexpectedly start and injury may occur.
*2 Using the hook
WARNING
When using the hook, ensure the unit is securely
suspended to avoid the risk of falling.
If the unit falls, an accident may occur.
INSTALLING (REPLACING) SAW
CHAIN
WARNING
○ To prevent accidents, always switch the unit off , and
remove the battery.
○ Don't use the saw chain or the guide bar other than
those specifi ed in "SPECIFICATIONS".
CAUTION
Wear thick gloves and be careful to avoid injury with the
saw chain.
NOTE
○ When removing the saw chain, remove sawdust from
the oil spout, oil hole, and guide bar groove.
If sawdust accumulates, this may cause the unit to fail.
○ Use the correct type of saw chain in accordance with
the specifi cations.
If you install the wrong type of guide bar, the saw chain
may come off and injury may occur.
1. Removing the side cover (Fig. 8)
Turn the nut and remove the side cover.
2. Removing the saw chain and guide bar (Fig. 9)
Rotate the tensioning screw in the "-" direction to
introduce a small amount of slack in the saw chain,
then detach from the sprocket. Detach along with the
guide bar in the direction indicated by the arrow.
3. Engaging the new saw chain in the sprocket
(Fig. 10)
Attach the saw chain from the guide bar tip. Make sure
the saw chain is oriented so that the blade faces in the
direction shown in the illustration below the sprocket.
Insert the bolt and chain tensioner boss into the hole in
the guide bar while holding the chain and guide bar tip.
Engage the end of the saw chain to the sprocket and
mount the guide bar to the saw body.
4. Installing the side cover (Fig. 11)
Attach the side cover by inserting the lug into the slot in
the saw body. Make sure the saw chain does not come
loose from the guide bar.
Rotate the nut once to temporarily fi x it.
Remove any dirt around the side cover before
reattaching.
5. Adjusting the saw chain tension (Fig. 12)
○ While lifting the guide bar tip, turn the tensioning screw
Figure Page
to adjust the saw chain tension.
5 2
○ Turn the tensioning screw to the "+" to increase the saw
chain tension, and to the "-" to decrease it.
7 2
6. Checking the saw chain tension (Fig. 13)
Adjust the saw chain tension so that the gap between
19 4
the saw chain drive link and the guide bar is 0.5 to 1 mm
― 325
when you lift the saw chain slightly near the center of
the guide bar.
7. Securing the nut (Fig. 14)
When adjustment is complete, lift up the guide bar, and
fully tighten the nut.
WARNING
After adjusting the saw chain tension, ensure the nut is
fully tightened.
If it is loose, injury may occur.
INSPECTION AND PREPARATION
PRIOR TO USE
Prior to use, make the following inspection and preparation.
WARNING
○ To prevent accidents, always perform steps 1 to 3
ensuring the battery is removed from the body.
○ Do not secure the lock-off lever in the slid position.
If the switch is accidentally engaged, the unit may
unexpectedly start and injury may occur.
1. Ensuring the switch is off
○ If you insert the battery without knowing whether the
switch is engaged, the unit may unexpectedly start,
which may result in an accident.
○ When the switch is engaged while the lock-off lever is
in the slid position, the unit switches on, and when the
switch is released, the unit switches off .
2. Checking the saw chain tension
○ If the saw chain tension is incorrect, there is a risk of
damage to the saw chain or guide bar and malfunction.
Referring to steps 5 to 7 "Installing (replacing) saw
chain," ensure an appropriate tension is set.
○ While the saw chain is still new, it is particularly
stretchy, so periodically check the tension and adjust
as required.
○ Also check the nut is securely tightened.
3. Checking the chain oil
○ This unit is delivered without chain oil inside. Ensure
the oil tank is fi lled with the chain oil provided before
use. (Fig. 15)
14