HIKOKI CS 3625DC Instrucciones De Manejo página 13

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 82
3. Charging
When inserting a battery in the charger, the charge
indicator lamp will blink in blue.
When the battery becomes fully recharged, the charge
indicator lamp will light up in green. (See Table 1)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be
as shown in Table 1, according to the condition of the
charger or the rechargeable battery.
Table 1
Charger
Status of indicator
status
lamp
ON/OFF at 0.5 sec.
Before
intervals (RED)
charging
Lights for 0.5 sec.
at intervals of 1 sec.
(BLUE)
Lights for 1 sec. at
While
intervals of 0.5 sec.
charging
(BLUE)
Lights continuously
(BLUE)
Lights continuously
(GREEN)
Charging
complete
(Continuous buzzer
sound: about 6 sec.)
ON/OFF at 0.3 sec.
Overheat
intervals (RED)
standby
ON/OFF at 0.1 sec.
intervals (PURPLE)
Charging
impossible
(Intermittent buzzer
sound; about 2 sec.)
*1 If the red lamp continues to blink even after the charger
has been attached, check to confi rm that the battery
has been fully inserted.
*2 Although charging will start once the battery has
cooled down even when left in situ, the best practice
is to remove the battery and allow it to cool down in a
shaded, well-ventilated location before charging.
*3
○ Fully insert the battery.
○ Check to confi rm that no foreign matter is stuck to the
battery mount or terminals.
<If charging takes a long time>
○ Charging will take longer at extremely low ambient
temperatures. Charge the battery in a warm location
(such as indoors).
○ Do not block the air vent. Otherwise the interior will
overheat, reducing the charger's performance.
○ If the cooling fan is not operating, contact a HiKOKI
Authorized Service Center for repairs.
(2) Regarding the temperatures and charging time of the
Indication meaning
Plugged into power
source *1
Charged at less
than 50%
Charged at less
than 80%
Charged at more
than 80%
Battery overheated.
Unable to charge. *2
NOTE
Malfunction in
CAUTION
the battery or the
charger *3
4. Disconnect the charger's power cord from the
5. Hold the charger fi rmly and pull out the battery.
NOTE
(1) Recharge the batteries before they become completely
13
rechargeable battery
The temperatures and charging time will become as
shown in Table 2.
Table 2
Model
Type of battery
Charging voltage
Temperatures at which the battery
can be recharged
1.5 Ah
2.0 Ah
2.5 Ah
Charging time for
3.0 Ah
battery capacity,
approx.
(At 20°C)
4.0 Ah
5.0 Ah
6.0 Ah
8.0 Ah
1.5 Ah (× 2 unit)
Multi
volt
2.5 Ah (× 2 unit)
battery
4.0 Ah (× 2 unit)
Number of battery cells
Charging voltage for USB
Charging current for USB
Weight
The recharging time may vary according to temperature
and power source voltage.
When the battery charger has been continuously used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 15 minutes rest until the next charging.
receptacle.
Be sure to pull out the battery from the charger after
use, and then keep it.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the fi rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
English
UC18YSL3
Li-ion
14.4–18 V
0°C–50°C
15 min
20 min
25 min
20 min
(BSL1430C,
BSL1830C: 30 min)
26 min
(BSL1840M: 40 min)
32 min
38 min
52 min
20 min
32 min
52 min
4–10
5 V
2 A
0.6 kg
loading

Este manual también es adecuado para:

Cs 3630dc