Machine Connection; Water Tank; Circuit Priming; Coffee Brewing - Saeco nina Cappuccino Instrucciones Para El Uso

• Do not place the machine on hot surfaces or near open
The coffee machine is now ready to be connected to the
power supply.
Note: It is recommended to wash the components
they have not been used for a certain period of time.
4.3

Machine Connection

Electric power can be dangerous! It is therefore
essential to follow the safety regulations
carefully. Do not use faulty cords! Faulty cords and
plugs must be immediately replaced by authorized
service centres.
Appliance voltage has been pre-set by the manufacturer.
Make sure that the power voltage matches the indications
• Make sure that the ON/OFF button (2) is not pressed
before connecting the machine to the power supply.
• Fit the plug into a wall socket with suitable power
voltage.
4.4

Water Tank

• (Fig.1) - Remove the water tank (3).
• (Fig.2)
• (Fig.1) - Insert the water tank making sure that it has
properly been replaced in its former seat.
Use only fresh, non-sparkling drinking water to
may damage the tank. Do not turn on the machine with
empty water tank: make sure there is enough water in
the tank.
4.5

Circuit Priming

Before starting the machine after a long period of
inactivity and after ejecting steam, the machine circuit
needs to be primed.
• (Fig.3) - Press the ON/OFF button (2).
• (Fig.4) - Place a container under the steam spout.
• (Fig.5) - Open the "hot water/steam" knob (4) by turning
it anticlockwise.
• (Fig.6) - Switch the selection knob to the "
(17).
(Pannarello).
• (Fig.6) - Switch the selection knob to the "
(17).
• Close the "hot water/steam" knob (4) by turning it
clockwise. Remove the container.
The machine is now ready to operate. Please see the
related sections for coffee brewing operating details.
• 16 •
4.6 Drip Tray Adjustment
The drip tray can be adjusted according to the cup size.
To adjust the drip tray height, do as follows.
• (Fig.24) - Lift the drip tray and remove the grill.
• (Fig.25) - Remove the support under the drip tray.
• (Fig.26 - 27) - Rotate the support and place it in the coffee
machine.
• (Fig.28) - Put the drip tray on the support and replace the
grill.
5

COFFEE BREWING

Warning! During the coffee brewing, do not
turning it clockwise. Danger of burns.
• During this operation, the "machine ready" light (15) may
operating mode.
• Before using the machine, make sure that the hot water/
steam knob (4) is closed and that there is enough water
in the tank.
• (Fig.3) - Press the ON/OFF button (2).
• Wait until the "machine ready" light (15) turns on. The
machine is now ready for coffee brewing.
5.1

Using Ground Coffee

• (Fig.7)
(10).
• (Fig.8A) - Insert the adapter (12) into the pressurized
• (Fig.11)
bottom (6).
• (Fig.12)
in place.
• (Fig. 14)
the selection knob (17) to the "
coffee brewing.
knob (17) to the "
• (Fig.16)
turning it from right to left and drain any water left. There
" position
• (Fig.9A) - Add 1- 1.5 measuring scoop for single coffee
and 2 measuring scoops for double coffee. Remove any
• (Fig.11)
"position
the bottom (6).
• (Fig.12)
in place.
• (Fig.13) - Take 1 or 2 preheated cups and place them
correctly placed under the coffee dispensing holes.
• (Fig.14) - Turn the selection knob (17) to the "
position.
" position until some
" position in order to stop brewing.
"