Chamberlain LiftMaster PROFESSIONAL ART300 Serie Instalación Mecánica página 7

GATE FITTING
For steel gates, fixings should be welded on or through bolted. When
through bolting the gate, use large washers or a plate on the other side.
The drive mechanism exerts an extremely high force on this joint.
Fixings must be through bolted for wooden gates. Wood deflects under
load and the bolt will become loose. Due to movement caused by
repeated loading, the wood deflects more and more until the gate no
longer closes correctly and has to be repaired.
The arm should not be mounted while fully extended (see Fig. 4). The
drive is self-locking. Mount the drive provisionally (e.g. with finger-tight
thumb-screws), and check the mounting position by opening the gate
manually.
MICRO SWITCHES
The micro switches installed on the inside of the ART300XXX (24V) are
not meant as limit switches, if the CB24 and CB124 controls are used.
They generate a pulse for the control.
Gate closed
Adjustment: The two superposed cams activating the micro switches
are to be adjusted in a way that they trigger between the open position
and the closed position. The cams are not especially assigned for open
or closed position.
The correct adjustment can be checked very easily when the operator is
disengaged. The micro switches make a "clicking sound" when
triggered.
Using a flat screwdriver, adjust the cams so that one cam triggers
approximately in the first third, the other one approximately in the last
third of the gate movement. (see illustration)
Having a problem?
Both cams are triggered at once.
In this case the travel cannot be set and the control flashes.
Remedy: Enlarge distance between cams.
Operator does not accept travel.
Remedy: Are both micro switches triggered correctly as described?
In this case, check if motorcabel is interchanged.
SAFETY MEASURES
A WING GATE OPENER SHOULD ALWAYS BE OPERATED IN
CONJUNCTION WITH CONTACT STRIPS AND / OR LIGHT
BARRIERS AS SAFETY FEATURES.
Please ensure that you comply with the standards, regulations and
safety devices applicable to your particular case.
Should the force generated by the moving wing at its
closing edge exceed 400 N, additional safety features must
be fitted suitable for the application.
All manuals and user guides at all-guides.com
Closed position
Gate open
FINAL REMARKS
Arrange the handover of the wing gate opener with your customer Make
sure that persons will operate the gate are familiar with its functions and
can operate them without problems. Have your customer practice
operating the gate until he is fully acquainted with all the following:
• Main switch.
• Rules of operation (e.g. do not drive through while the gate is still
opening).
• Additional safety features (photoelectric barrier, contact strip, flashing
lights, etc.).
• Switch to manual operation in case of power failure.
• Provide the customer with a full set of instructions. Inform him to keep
them in a safe place and read them when possible.
• Reference a checklist, so that you have a record of which functions
have been explained and of any points not dealt with.
ACCESSORIES
Model 94335E 3-channel mini transmitter, 433.92MHz
Model 9747E Keypad, 433.92MHz
Model 760E Key switch
Model 100027 1-Function Keyswitch, surface mount
(Flush mount - 100010)
Model 100041 2-Function Keyswitch, surface mount
(Flush mount - 100034)
Model 100263 Infrared barrier
Model 203285 E-Lock 12 Volt
Model 203292 Loop Detector 1 Channel
Model 203308 Loop Detector 2 Channel
Model 203315 Standard Hardstop
Model 203322 Hard Stop High
Model 203339 Mechanical Floor Lock for Double Wings
Model 600008 IR Sensor Stand - 530mm
Model 600015 Key Switch Stand - 1100mm
Model 600046 2.5 Safety Edge Set (Small)
Model 600053 20m Bulk Pack Safety Edge Profile (Small)
Model 600060 Assembly Pack Safety Edge (Small)
Model 600077 Bulk pack (not shown)
Model 600091 Main switch
Model 600138 20m Bulk Pack Safety Edge Profile (Medium)
Model 600145 20m Bulk Pack Safety Edge Profile (Large)
Model 600152 Assembly Pack Safety Edge
(Medium/Large)
Model 600169 1m (3.2 ft.) Safety Edge Profile (Medium)
Model 600176 1m (3.2 ft.) Safety Edge Profile (Large)
Model 600213 Interface Box for Safety Edges
TECHNICAL DATA
Modell
Voltage in
Voltage out (Motor)
Power
Current (max)
Current (no load current)
Torque
Motor speed
Duty cycle (max)
Working temperature range
Protection class
Degree of protection
Weight
Max. gate wing lenght
Max. gate weight at max. wing lenght
incl. 20% reserve
ART300XXX (24V)
230V AC/24AC/24VDC
24VDC
60W
2,5A
0,3A
280Nm
1800rpm
50 cycles/h
deg C -20°C/+55°C
I
IP44
9Kg
2,5m
300Kg