Metabo KGSV 216 M Instrucciones De Manejo página 8

en ENGLISH
 Cut thin or thin-walled workpieces only with fine-
toothed saw blades.
 Always use sharp saw blades. Replace
damaged saw blades immediately. There is an
increased risk of kickback if a blunt sawtooth
gets caught in the workpiece's surface.
 Do not jam workpieces.
 If in doubt, check workpiece for inclusion of
foreign matter (e.g. nails or screws).
 Never cut several workpieces at the same time
– and also no bundles containing several
individual pieces. Risk of personal injury if
individual pieces are caught by the saw blade
uncontrolled.
 When making grooves avoid lateral pressure on
the saw blade - use a clamping device.
Drawing-in/trapping hazard!
 Ensure that during operation no parts of the
body or clothing can be caught and drawn in by
rotating components (no ties no gloves, no
clothes with wide sleeves; contain long hair with
a hairnet).
 Never cut workpieces to which ropes, cords,
strings, cables or wires are attached or which
contain such materials.
Hazard generated by insufficient
personal protection gear!
 Wear hearing protection.
 Wear protective goggles.
 Wear dust mask.
 Wear suitable work clothes.
 Wear non-slip footwear.
 Wear gloves when handling saw blades and
rough tools. Carry saw blades in a container.
Risk of injury by inhaled wood dust!
 Work only with a suitable dust collector attached
to the saw. The dust extraction unit must comply
with the values stated in chapter 15..
Reduce dust exposure:
 Some dust created by using this power tool may
contain chemicals known to cause cancer,
allergic reaction, respiratory disease, birth
defects or other reproductive harm. Some
examples of such substances are, lead (in paint
containing lead), additives used for wood
treatment (chromate, wood preservatives),
some wood types (such as oak or beech dust).
 The risk from these exposures depends on how
long you or bystanders are being exposed.
 Do not let particles enter the body.
 To reduce your exposure to these chemicals:
work in a well ventilated area, and work with
approved safety equipment, such as dust
masks that are specially designed to filter out
microscopic particles.
 Observe the relevant guidelines for your
material, staff, application and place of
application (e.g. occupational health and safety
regulations, disposal).
 Collect the generated particles at the source,
avoid deposits in the surrounding area.
 Use the supplied dust collection unit and a
suitable extraction unit. This ensures that fewer
particles enter the environment in an
uncontrolled way.
 Reduce dust exposure with the following
measures:
– Do not direct the escaping particles and the
exhaust air stream at yourself or nearby
persons or on dust deposits.
– Use an extraction unit and/or air purifiers
– Ensure good ventilation of the workplace and
keep clean using a vacuum cleaner Sweeping
or blowing stirs up dust
– Vacuum or wash the protective clothing Do not
blow, beat or brush
8
Hazard generated by modification of
the machine or use of parts not tested and
approved by the equipment manufacturer!
 Assemble tool in strict accordance with these
instructions.
 Use only parts approved by the equipment
manufacturer. This applies especially for:
– saw blades (for order numbers, refer to
chapter 11. Accessories).
– Safety devices.
– Cutting laser
– Illumination of cutting line
 Do not change any parts.
 Ensure that the speed indicated on the saw
blade is at least the same as the speed
indicated on the saw.
Hazard generated by tool defects!
 Before every use check tool for possible
damage: before operating the tool all safety
devices, protective guards or slightly damaged
parts need to be checked for proper function as
specified. Check to see that all moving parts
work properly and do not jam. All parts must be
correctly installed and fulfil all conditions
necessary to ensure perfect operation of the
unit.
 Do not used any damaged or contorted saw
blades.
Risk of injury by noise!
 Wear hearing protection.
Danger from blocking workpieces or
workpiece parts!
If blockage occurs:
1. switch machine off,
2. Pull the mains plug or remove the detachable
battery pack,
3. wear gloves,
4. clear the blockage using a suitable tool.
3.2 Special safety instructions for
cordless machines:
Remove the battery pack from the machine before
making any adjustments, changing tools,
maintaining or cleaning.
Protect battery packs from water and
moisture!
Do not expose battery packs to fire!
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch contacts or short-circuit battery
packs!
A slightly acidic, flammable fluid may leak
from defective Li-ion battery packs!
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical attention
immediately!
Transporting li-ion battery packs: The shipping of
li-ion battery packs is subject to laws relating to the
carriage of hazardous goods (UN 3480 and UN
3481). Inform yourself of the currently valid
specifications when shipping li-ion battery packs. If
necessary, consult your freight forwarder. Certified
packaging is available from Metabo.
3.3 Symbols on the machine (depends
on model)
Read the operating instructions.
Never place hands into running saw
blade.
Wear protective goggles and ear
protectors.
Never operate the tool in a damp or wet
environment.
Laser radiation - Do not look into the light
beam.
.......... Class II Construction
V ............. volts
A............. amperes
Hz ........... hertz
.../min ..... revolutions per minute
~ ............. alternating current
.......... Direct current
n ............ rated speed
0
3.4 Safety devices
Retractable blade guard (6)
The retractable blade guard protects against
unintentional contact with the saw blade and from
chips flying about.
Safety lock (27)
Cordless tools: The machine can only be
switched on when the safety lock is activated.
Mains-powered tools: The retractable blade
guard opens and the saw can be lowered only
when the safety lock is activated.
Parallel guide/ ripping fence (26)
The parallel guide/ ripping fence prevents that the
workpiece can be moved during the cutting
process. During operation, the parallel guide/
ripping fence always has to be installed.
Make sure the additional profile (35) is set
correctly to support the workpiece in the best
manner possible and will not interfere with the
blade or the guard. Lock using the set screw (36).
An incorrectly adjusted additional profile (35) can,
in the event of sloped cuts and double mitre cuts,
get in contact with the saw blade and thus lead to
serious injuries.
An incorrectly adjusted additional profile (35) can,
in the event of sloped cuts and double mitre cuts,
get in contact with the saw blade and thus lead to
serious injuries.
The additional profile (35) at the parallel guide/
ripping fence has to be moved for inclined cuts
after loosening the set screw (36).
4. Overview
See page 2.
The illustrations are regarded as exemplary for all
devices. Therefore, the equipment of your device
may differ from the illustrations.
1 Closing the chip bag
2 Chip bag
3 Chip extraction nozzle
4 Laser beam egress point
5 Cutting line illumination
6 Retractable blade guard
7 Longitudinal stop
8 Table
9 Turntable
10 Table insert
11 Locking lever for turntable
12 Safety catch for stop positions of the turntable*
13 Set screw for pulling device*
14 Allen key / tool storage for Allen key
15 Work clamp
16 Table extension
17 Locking screw of the table width extension
18 Saw blade lock
19 Saw handle
20 Speed adjustment wheel *
21 Handle
22 Hook for cable winding
23 Locking lever for setting the angle of inclination
24 Locking button (to extend the angle of
inclination by +/- 2 °)
25 harp
26 Parallel guide / ripping fence
27 Safety lock
28 ON/OFF switch of the saw (the hole in the
switch should be used to secure the machine
with a padlock from being switched on by
unauthorised persons)