Bosch 0 601 B22 503 Manual Original página 34

All manuals and user guides at all-guides.com
OBJ_BUCH-1128-004.book Page 34 Wednesday, April 15, 2015 4:58 PM
34 | English
Ceiling Strips/Mouldings (According to US Standard)
When the ceiling strips/mouldings are to be sawn lying flat on the saw table, the standard mitre angles
52°
of 31.6° (horizontal) and 33.9° (vertical) must be set.
The following table contains instructions for sawing ceiling strips/mouldings.
38°
Settings
Bevel angle
Ceiling strip/moulding
Inner corner Horizontal mitre angle
Positioning of work-
piece
The finished
workpiece is located ...
Outer corner Horizontal mitre angle
Positioning of
workpiece
The finished
workpiece is located ...
Checking and Adjusting the Basic Adjustment
 Before any work on the machine itself, pull the mains
plug.
To ensure precise cuts, the basic adjustment of the machine
must be checked and adjusted as necessary after intensive use.
A certain level of experience and appropriate specialty tools are
required for this.
A Bosch after-sales service station will handle this mainte-
nance task quickly and reliably.
Setting the Standard Bevel Angle 0° (Vertical)
– Bring the machine into the transport position.
– Turn the saw table 16 to the 0° detent 15. The lever 13
must be felt to engage in the detent.
Checking: (see figure S1)
– Set an angle gauge to 90° and place it on the saw table 16.
The leg of the angle gauge must be flush with the saw blade 7
over the complete length.
Adjusting: (see figure S2)
– Loosen the lock lever 14.
– Loosen set screws 64 and 65 with the supplied open-end
spanner 42 (10 mm).
– Loosen set screw 63 (approx. 3 turns) with the supplied
hex key 33 (4 mm).
– Screw set screw 60 (10 mm) in or out until the leg of the
angle gauge is flush with the saw blade over the complete
length.
1 609 92A 19J | (15.4.15)
Placed
against the
fence
52°
0°
Left side Right side
45° right 45° left
Bottom edge Bottom edge
against the fence against the fence
... to the right of the ... to the left of the
cut cut
45° left 45° right
Bottom edge Bottom edge
against the fence against the fence
... to the right of the ... to the left of the
cut cut
– Retighten the lock lever 14 again.
Afterwards, tighten set screw 63 first, and then set screws
64 and 65.
When the angle indicators 31 and 22 are not in line with the
0° marks of scale 30 after adjusting, loosen the fastening
screws of the angle indicators with the supplied cross-head
screwdriver 33 and align the angle indicators alongside the 0°
marks.
Setting the Standard 45° Bevel Angle (Leftward)
– Bring the power tool into the working position.
– Turn the saw table 16 to the 0° detent 15. The lever 13
must be felt to engage in the detent.
– Pull the left fence extension 19 completely outward.
– Loosen the lock lever 14 and tilt the tool arm leftward to
the stop (45°) by the handle 5.
Checking: (see figure T1)
– Set an angle gauge to 45° and place it on the saw table 16.
The leg of the angle gauge must be flush with the saw blade 7
over the complete length.
Adjusting: (see figure T2)
– Screw set screw 64 (10 mm) in or out until the leg of the
angle gauge is flush with the saw blade over the complete
length.
– Retighten the lock lever 14 again.
When the angle indicators 31 and 22 are not in line with the
45° marks of scale 30 after adjusting, firstly once more check
the 0° setting for the bevel angle and the angle indicators.
Then repeat the adjustment of the 45° bevel angle.
Lying flat on
the saw table
33.9°
Left side Right side
31.6° right 31.6° left
Upper edge against Bottom edge
the fence against the fence
... to the left of the ... to the left of the
cut cut
31.6° left 31.6° right
Bottom edge Upper edge against
against the fence the fence
... to the right of the ... to the right of the
cut cut
Bosch Power Tools