Idiomas disponibles
Idiomas disponibles
Practical advice
Marking the cutting line (see figure N)
Two laser beams indicate the cutting width of the saw blade.
This allows for exact positioning of the workpiece for sawing,
without having to open the retracting blade guard.
– Switch on the laser beams with the switch (34).
– Position your mark on the workpiece between the two
laser lines.
Note: Before sawing, check if the cutting width is still indic-
ated correctly Adjusting the Laser. Vibrations during intens-
ive use, for example, can cause the laser beams to become
misaligned.
Permissible workpiece dimensions
Mitre angle
Bevel angle
0°
0°
45°
0°
0°
45° (left)
0°
45° (right)
45°
45° (left)
45°
45° (right)
A) With distance stop (see figure O)
B) With spacer for slide mechanism (see figure R)
Minimum workpiece dimensions (= all workpieces that can
be secured left or right of the saw blade using the supplied
screw clamp (40)): 200 mm x 40 mm (length x width)
Adjusting the Depth Stop (Sawing the Groove) (see
figure P)
The depth stop needs to be adjusted if you wish to saw a
groove.
– Swivel the depth stop (42) forwards.
– Swivel the tool arm by the handle (13) into the required
position.
– Turn the adjusting screw (41) until the end of the screw
touches the depth stop (42).
– Slowly guide the tool arm upwards.
Sawing workpieces of the same length (see figure Q)
The length stop (54) (accessory) can be used for easily saw-
ing workpieces of the same length.
The length stop can be mounted on either side of the saw
table extension (29).
– Loosen the locking screw (55) and move the length
stop (54) over the clamping screw (56).
– Re-tighten the locking screw (55).
– Set the saw table extension (29) to the required length.
Bosch Power Tools
Sawing wider mouldings (see figure R)
For sawing wider mouldings (max. height of 175 mm), use
the spacer (7).
– If tightened, loosen the locking screw (6) and pull the tool
arm forwards.
– Move the spacer (7) down onto the slide mechanism (37)
and slide the tool arm as far back as possible.
– Re-tighten the locking screw (6).
Special workpieces
When sawing curved or round workpieces, these must be es-
pecially secured against slipping. At the cutting line, there
should be no gap between the workpiece, fence and saw
table.
If necessary, you will need to manufacture special fixtures.
Height x width
Replacing insert plates (see figure S)
[mm]
The red insert plates (21) can become worn after prolonged
85 x 370
use of the power tool.
A)
70 x 400
A)
Replace faulty insert plates.
120 x 200
B)
175 x 60
– Bring the power tool into the work position.
– Loosen the screws (57) using the hex key (6 mm) (39)
85 x 250
B)
and remove the old insert plates.
175 x 20
– Insert the new right-hand insert plate.
60 x 360
– Screw the insert plate as far as possible to the right with
38 x 370
the screws (57) so that the saw blade does not come into
60 x 240
contact with the insert plate over the entire length of the
38 x 250
possible slide motion.
– Repeat the work steps in the same manner for the new
left-hand insert plate.
Adjusting the laser
Note: To test the laser function, the power tool must be con-
nected to the power supply.
While adjusting the laser (e.g. when moving the tool
u
arm), never activate the on/off switch. Starting the
power tool accidentally can lead to injuries.
– Bring the power tool into the work position.
– Turn the saw table (20) to the 0° detent (27). The lever
(24) must be felt to engage in the detent.
Checking (see figure T1)
– Draw a straight cutting line on the workpiece.
– Slowly guide the tool arm downwards using the
handle (13).
– Position the workpiece so that the teeth of the saw blade
line up with the cutting line.
– Hold the workpiece in this position and slowly guide the
tool arm back up.
– Clamp the workpiece.
– Turn on the laser beam using the switch (34).
The laser beam must be flush with the cutting line on the
workpiece along its entire length, even if the tool arm is
guided downwards.
Adjusting the flush alignment (see figure T2)
1. Adjusting the right-hand laser beam:
English | 39
1 609 92A 8L3 | (06.03.2023)
