Idiomas disponibles
Idiomas disponibles
English
DESCRIPTION (Fig. A)
WARNING :
Never modify the power appliance or
any part of it. Damage or personal injury could result.
Top handle/cord wrap
1
Power cord
2
On/off
control
switch
3
Vacuum head
4
Lid latches
5
Dust tank
6
Hose
7
Casters
8
Clean connect
lter
9
TM
Vacuum port
10
Hose strap
11
12
Disposable dust bag
ASSEMBLY AND ADJUSTMENTS (Fig. A–C)
WARNING: To reduce the risk of injury, turn
appliance off and disconnect appliance from
power source before installing and removing
accessories, before adjusting or changing
set-ups or when making repairs.
start-up can cause
injury.
WARNING:
The lter
9
place while vacuuming, except as described
under
WET PICK UP APPLICATIONS
OPERATION. When vacuuming ne dust, you
may also need to use an disposable dust bag to
make emptying the dust tank easier.
1. Install the disposable dust bag
in
Fig.
B.
NOTE: Be careful not to tear the bag. Place bag
securely onto vacuum port
seal for maximum dust collection performance.
2. Place the vacuum head
secure it by closing the lid latches
3. Insert the end of hose
port
and tighten the end of hose to the tank.
10
OPERATION
INSTRUCTIONS FOR USE (Fig. A, D, E)
WARNING:
Always observe the safety instructions
and applicable regulations.
1. Plug the power cord into an appropriate outlet.
2. Turn the on/off switch
3
3. The D
WALT construction dust extractor is tted
E
with the D
WALT connection system. It allows a
E
fast, secure connection between the hose
and power tool. The connector
7
directly to D
WALT compatible tools or through the
E
use of an adapter (available from local D
supplier). If you need Install the adapters, refer to
Fig.
E.
NOTE:
If using an adapter ensure it is rmly
attached to the tool outlet before following the steps
below.
An accidental
must always be in
under
, as shown
12
to provide a tight
10
onto the dust tank and
4
.
5
into clip-in hose vacuum
7
to the ON position ( I ).
connects
13
WALT
E
OPERATING INSTRUCTIONS
CASTER INSTALLATION (Fig. A, F)
1. Invert the dust tank and install the casters to the
bottom of the dust tank and x them with screws.
2. Return dust tank assembly upright.
REMOVE/CHANGE USED DISPOSABLE
DUST BAG (Fig. A)
WARNING:
Appropriate personal protective
equipment like dust mask and gloves should be used
while handling used dust bags.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch lid latches
5
3. Pull the disposable dust bag
port
.
10
4. Seal the disposable dust bag
removing it from the machine.
5. Dispose the disposable dust bag
container according to statutory provisions.
WET PICK UP APPLICATIONS (Fig. A, G)
WARNING:
If foam or liquid escapes from the
machine,switch off immediately.
WARNING:
Do not use the machine with this set
up for dust Class L.
The ball oat
will block air to the motor when
14
the dust tank is full and the sound of the motor will
change at once.
When the motor has a high pitched sound and air/
water ow stops, empty the dust tank.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch lid latches
5
head
.
4
3. Empty contents of dust tank
or drain.
CAUTION:
Clean the water level limiting device
regularly and examine it for signs of damage. Refer to
Fig.
G.
NOTICE:
DO NOT remove ball oat
will cause damage to the vacuum. The ball oat keeps
water from entering the motor.
Before using the vacuum for wet pick up:
• Ensure the dust tank is empty and free of excessive dust.
• Remove the lter
.
9
TO CONVERT BACK TO DRY VACUUM
OPERATION (Fig. A)
1. Empty dust tank, refer to
instructions.
2. Place dust tank upside down position until dry. DO
NOT use wet dust tank for dry pick up.
3. Place vacuum head
4. Reinstall lters when vacuum head is dry. See Filters
under Maintenance.
5. When dust tank is dry place the vacuum head
onto the dust tank and secure it by closing the
lid latches
.
5
18
and remove vacuum head
carefully from vacuum
12
opening tightly when
12
in appropriate
12
and remove vacuum
into a suitable container
6
, doing so
14
TO EMPTY DUST TANK
on a level surface appliance dry.
4
4
.
4
