Hendi 221099 Manual Del Usuario página 7

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 47
Main parts of the product
(Fig.1 on page 3)
1. Handle
2. Lid
3. Casing
4. Block juice cover
5. Cone
6. Bowl
7. Motor base
8. Switch
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Operating instructions
• Connect the power plug to a suitable electrical outlet.
• Switch on the power switch to the position "I". Green indicator
lights up.
• Align the centre of the fruit with the juicer head. And put the
handle down. Press the handle down with some force to make
juicer head rotate.
• Repeat above operation and change to another fruit if no more
juice coming out from the spout.
Note: 1. Empty the cone regularly to avoid overflow or jamming.
2. WARNING: Kitchen utensils should not be used under
any circumstances to push the fruit into the appliance.
This will damage to the appliance.
Overheat protection
There is a built-in motor thermal cut-out to protect the motor
from overheating.
• When the motor is running very slowly or it stops, this thermal
cut-out activates.
• To reset it, switch OFF the appliance to the "0" position and
unplug it.
• Leave the appliance for cooling down for about 30 minutes.
• Then, the appliance can be used again after switch ON.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
• DANGER OF INJURY! Care should be taken when handling
the sharp cutting blades during cleaning.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Clean the inside of container with a non-abrasive detergent
and rinse with clean water.
• Never immerse the appliance in water or other liquids.
• No parts are dishwasher safe.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
GB
7
loading