Idiomas disponibles
Idiomas disponibles
Parts and Functions
Indoor Unit
Inlet
Inlet grille
Outlet
Vertical blade
(adjust left and
r ight air fl
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
Please be subject to the actual produce purchased the
above picture is just from your reference
Display board
1
2
1
Signal receiver hole
2
ON/OFF
display
3
Ambient temp.display
When receiving the remote
control signal, display the set
temperature and in the rest
time the room temperature is
displayed and this room
temperature is only for reference.
Outdoor Unit
OUTLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
INLET
Please be subject to the actual produce purchased the
above picture is just from your reference
Air Purifying Filter
(inside)
Emergency
Switch
ow)
Display board
4
5
3
4
TIMER ON\OFF display
TIMER ON-OFF display
SLEEP display
Note to the power failure resume:
press the sleep button ten times in five seconds
and enter function after hearing four sounds.And
press the sleep button ten times within five
seconds and leave this function after hearing
two sounds.
5
COOL\HEAT\Dry\ AUTO
display
4
Remote controller
1
6
2
7
3
4
5
8
9
18
10
19
11
20
12
21
13
22
14
23
15
24
16
25
17
1. Mode display
Operation mode
AUTO
COOL
DRY
HEAT
FAN
Remote controller
2. Signal sending display
3. SWING display
4. FAN SPEED display
Display
circulated
LO
MED
HI
AUTO
5. LOCK display
6. TIMER OFF display
TIMER ON display
7.TEMP display
Healthy function is not available for some units.
Loading of the battery
4
Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change- over
type fluorescent lamp or
wireless telephone is installed in the
room, the recei
ver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batte
ries have been used up. Please change batteries.
If the remote controller can't run normally during operation, please
remove the batteries and
reload several minutes later.
Hint:
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.
8.
Additional functions display
Supplemented
electrical
Operation mode
QUITE
SLEEP
HEALTH
heating
Remote controller
9. QUIET button
10. HEAT button
11. COOL button
12. AUTO button
13. FAN button
14. TIMER button
15. HEALTH button
16. LOCK button
Used to lock buttons and LCD display.
17. LIGHT button
Control the lightening and extinguishing
of the indoor LED display board.
18. POWER ON/OFF button
19. DRY button
20. TEMP button
21. SWING button
22. HOUR button
23. EXTRA FUNCTION button
Function: Air sending--- Healthy airflow
position1--- Healthy airflow position 2
--- Restore the original flap position
--- Right & left air airflow--- A-B yard---
10 and heating symbol displayed
simultaneously--- Sleeping--- Electrical
heating--- Refresh air(
reserved function
--- Power--- Fahrenheit/Celsius mode
conversion
24.CANCEL/CONFIRM button
Function: Setting and cancel to the
timer and other additional functions.
25. RESET button
When the remote controller
appears abnormal, use a sharp
pointed article to press this button
to reset the remote
1
Remove the battery cover;
2
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
3
Be sure that the loading
e" + "/"-";
is in line with th
POWER
)
1
