Idiomas disponibles
Idiomas disponibles
How To Use
Power ON/OFF Button
Plug unit in to a 120 volt AC electrical outlet. Press the POWER button to turn unit on. Press the
POWER button again to turn unit off. ATTENTION: When the water in the tank is almost empty, the
unit will shut off to indicate to the user to refill water.
Mist Adjustment Setting
Mist adjusts from Lowest output 1 to Highest output 5. To increase the mist output, press the MIST
INCREASE + button. The corresponding Mist Level will be lit on the LED display. To decrease mist
output, press the MIST DECREASE - button.
Mist Temperature Setting
When the humidifier is powered ON, it will be operating on the last setting used. To change the
Mist Temperature from Cool Mist to Warm Mist, press the WARM button. The mist temperature will
change to Warm Mist, and WARM will be lit on the button. To change the Mist Temperature back to
Cool Mist, press the WARM button again. The mist temperature will change to Cool Mist, the WARM
illumination will turn off. NOTE: Once warm mist is selected, it will take 20 minutes to heat up before the
mist becomes warm.
Programmable Humidistat
This unit has a Programmable Humidistat that can be set in 5% increments from 35%-70% humidity.
To program the humidity level, press the HUMIDISTAT+ button. The humidity level will increase by
5% every time the button is pressed, and will show on the LED display screen. Keep pressing the
HUMIDISTAT+ button until the desired humidity level setting is reached. The LED display will show
the set humidity level for 3 seconds, then will default back to display the current humidity. To decrease
the humidity level setting, press the HUMIDISTAT - button. The humidity level will decrease on the
LED display by 5%. Keep pressing the HUMIDISTAT - button until the desired humidity level setting
is reached.
NOTE: To eliminate any programmed Humidistat setting, press the HUMIDISTAT+ button until you
reach "CO" level (One level above 70%).
NOTE: When the set humidity level is reached, the humidifier will CYCLE OFF until the humidity in
the room drops 2% below the set humidity level, then will CYCLE ON until the set humidity level is
again reached.
Night Light / Display Lights
Press the LAMP button once to turn on the night light. The light at the bottom of the water tank will
turn on, illuminating the tank. Press the LAMP button a second time to leave the night light on, but
turn off display panel. Press the LAMP button a third time to turn off the night light and display light
so there are no lights on the unit. Press the LAMP button a fourth time to turn the display lights on.
Timer
Press the TIMER button. Keep pressing the TIMER button until the desired timer setting is lit on the
display. The timer button will cycle through the following settings 0 hours, 2 hours, 4 hours, 8 hours,
12 hours, 18 hours, 24 hours, 0 hours. To turn the timer OFF, press the TIMER button until 0 hours is
shown on the display. NOTE: Always be sure the humidifier has a full tank of water prior to using the
timer setting.
6
How to Fill
CAUTION: Before filling unit with water, turn the power off and unplug the unit from the outlet.
NOTE: Always use two hands to carry the water tank.
1. Grasp tank handle and lift up from humidifier base. (Fig. 3)
Fig. 3
2. Turn the tank upside down—remove the tank cap by turning it
Fig. 4
counter-clockwise. (Fig. 4)
Fig. 5
3. Fill the water tank with clean, cool (not cold) water. We
recommend using distilled water if you live in a hard water area.
(Fig. 5)
NOTE: Not for use with essential oils. Even a few drops can ruin the
humidifier.
Fig. 6
4. Replace the tank cap by turning clockwise until tight. (Fig. 6)
5. Install the tank back on the base of the unit. Make sure the tank is
Fig. 7
firmly seated. (Fig. 7)
NOTE: It is normal to have a small amount of water
in the base during and after use.
7
