EnGLIsH
•
Gin
•
Rum
•
Vodka
•
Tequila
•
Whiskey
Removing Bottles (Fig. E)
CAUTION: Avoid spills while removing bottles.
1. Lift the straw lock
8
.
2. Slide the straw plug
11
3. Pull the bottle stopper
straw
7
.
nOTE: If the cocktail maker pauses for an empty bottle and you
press mix without replacing the bottle, it will skip to the next bottle
in the recipe. If that bottle is empty, it will pause again. Refer to the
PAUSE MODE section for more information.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
sourcebattery pack before making any adjustments
or removing/installing attachments or accessories.
An accidental start-up can cause injury.
On/Off (Fig. F)
WARNING: Do not interact with the cocktail maker while
it is operating.
•
To turn the cocktail maker on, push the "I" side of the power
switch
14
. The 4 strength LEDs
blink. When they become solid, the cocktail maker is ready
to use.
•
To turn the cocktail maker off, push the "O" side of the power
switch. All LEDs will turn off.
Choose a Glass Tray (Fig. G)
Place a glass or shaker on either the glass shelf
tray
3
, depending on the height of the glass being used. Refer
to the cocktail image on the capsule
nOTE: A glass or shaker must be in place before making a drink
to avoid spillage.
short glass:
1. Pull the glass shelf down so it stands straight out from the
tower
18
.
2. Place a small glass on the glass shelf.
Tall glass:
1. Push the glass shelf up so it hides away in the tower.
2. Ensure the drip tray cover
3. Place a tall glass on the drip tray cover.
shaker:
18
and bottle off the cocktail maker.
13
out of the bottle and remove the
15
and 6 bottle LEDs
17
or drip
20
for glass style.
4
is in place.
The shaker LED
In this case, use a shaker instead of a tall glass.
1. Push the glass shelf up so it hides away in the tower.
2. Ensure the drip tray cover is in place.
3. Place a shaker on the drip tray cover.
Inserting a Capsule (Fig. H, I)
WARNING: Cut Hazard. Do not probe capsule holder area
with fingers.
WARNING: Pinch point. Keep away from capsule holder
when closing capsule holder lid.
WARNING: Use only Bartesian capsule. Use with any other
capsule may result in damage to the appliance.
IMPORTanT: Do not open capsule
IMPORTanT: Once the capsule is punctured, it may drip liquid.
To avoid this, place a capsule in the capsule holder
before mixing a drink.
1. Before inserting a capsule, place a glass or shaker on the glass
shelf
17
or drip tray
TRAY section
2. Select the capsule you wish to use.
3. To open the capsule holder, lift the capsule holder lid
it clicks into place.
4. Ensure the bar code
Wipe your thumb across the bar code before inserting
capsule into capsule holder.
5. Place the capsule in the capsule cup
holder. Ensure the capsule tab
cocktail maker will not operate if the capsule is inserted any
other way.
6. Ensure the capsule sits fully in the capsule cup.
nOTE: The scanner inside the capsule holder scans the code on
16
will
top of the capsule. This allows the cocktail maker to pull from
the correct bottles so it dispenses the correct drink.
7. Push the capsule holder lid down to close the capsule holder
until it clicks. Ensure the lid is fully closed before operating.
nOTE: If the capsule code is successfully read, the bottle
LEDs
16
will light under the bottles that are being used. Ensure
each bottle is in its correct place.
nOTE: If lights do not turn on, lift the capsule holder lid and use a
clean, dry towel to wipe the barcode scanner
barcode
32
as shown in Fig. I. Then, repeat step 6.
Select Alcohol Strength (Fig. J)
To select the amount of alcohol to be dispensed into the drink,
turn the strength selector dial
•
Left: less alcohol
Right: more alcohol
•
The strength LEDs
selector, indicating the strength of the drink.
•
- mocktail (no alcohol)
•
- light alcohol content
•
- regular alcohol content
•
- strong alcohol content
19
will light when a drink needs to be shaken.
20
.
3
as described in the CHOOSE A GLASS
is clean from liquid and debris.
32
23
24
faces to the left. The
25
.
15
will turn on and off as you turn the
21
just
22
until
located in the
31
and the capsule