Idiomas disponibles
Idiomas disponibles
TRANSLATION OF THE ORIGINAL
INSTRUCTIONS
BENCH GRINDER
NOTE: BEFORE THE POWER TOOL IS USED FOR THE FIRST TIME,
READ THIS INSTRUCTION MANUAL AND KEEP IT FOR FUTURE
REFERENCE.
DETAILED SAFETY REGULATIONS
BENCH GRINDER SAFETY WARNINGS
Do not use a damaged accessory. Before each use, inspect the
accessor such as abrasive wheels for chips and cracks and wire
brushes for loose or cracked wires. After inspecting and
instigating an accessory, position yourself and bystanders
away from the plane of the rotating accessory and run the
power tool at maximum no-load speed for one minute.
Damaged accessories will normally break apart during this test
time.
The rated speed of the accessory must be at least equal to the
maximum speed marked on the power tool. Accessories running
faster than their rated speed can break and fly apart.
Be aware that wire bristles are thrown by the wire brush even
during ordinary operation. Do not overstress the wires by
applying excessive load to the wire brush. The wire bristles can
easily penetrate light clothing and/or skin.
Never grind on the sides of a grinding wheel. Grinding on the
side can cause the wheel to break and fly apart.
EXPLANATION OF THE PICTOGRAMS USED
1
1. Warning! Take special precautions
2. WARNING Read the operator's manual
3. Use personal protective equipment (safety goggles, hearing
protection, dust mask)
4. Use protective clothing
5. Disconnect the power cord before starting maintenance or
repair work
6. Do not allow children to tools
7. Protect the device against moisture
8. CAUTION Always use eye protection
CONSTRUCTION AND USE
Bench grinder is designed for light-duty works in small
workshops and for individual, amateur activities (tinkering). It
is not intended for professional use. It is perfect for sharpening
tools such as drills and chisels. Grinder is not designed for
continuous use and it must not be used for more than 30 minutes
at a time. After operation at full load for this amount of time, switch
off the grinder for at least 30 minutes. You can install wire brushing
wheels provided that such brush can work at rotational speed
equal to 2850 rpm or higher.
Use the power tool according to the manufacturer's
instructions only!
59G383
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
1. Eye shield
2. Eye shield (magnifying)
3. Grinding wheel
4. Side cover
5. Hole for bench fixing
6. Base
7. Switch button
8. Adjustable workrest
9. Grinding wheel cover
10. Spark shield
11. Adjustable lamp
12. Drawer for tools
13. Wheel dresser
14. Rubber cushion
* Differences may appear between the product and drawing
EQUIPMENT AND ACCESSORIES
1. Eye shield
2. Spark shield
3. Workrest
4. Wheel dresser
5. Bolts, screws and washers– 1 set
PREPARATION FOR OPERATION
GRINDER INSTALLATION ON A WORKSHOP BENCH
Four rubber cushions (14) help to limit vibrations and sound
transfer. It is recommended to firmly fix the grinder to a workbench
or a stand with the use of two fixing points designed for such
purpose. They are located on the bench grinder base (fixing bolts
are not included) and guarantee safe operation. Hole for bench
fixing (5) is located at each side of the grinder. The holes allow to
use screws or bolts with diameters up to 10 mm. When the grinder
is to be installed on a metal work-bench it is recommended to put
a piece of wood under the grinder. Fixing screws should go
through the wooden base. Use of wood helps to limit vibrations.
When you use screws for installation do not remove four
rubber cushions (14). In case of direct fixing of the bench
grinder, ensure that:
- The surface under the grinder is flat and clean,
- Screws are equally tightened without excessive torque.
FIXING AND ADJUSTING EYE SHIELDS AND SPARK SHIELD
Prior to fixing of supports for eye shields ensure the grinder is
switched off and that its plug is removed from the mains
socket. Prior to every use of the grinder ensure the eye shields
(1) and (2) are properly installed. Eye shield must be installed
on appropriate support above each of the grinding wheels.
Magnifying eye shield (2) is characterised by a magnifying glass
that ensures better visibility of the processed spot and thus better
precision of the operation performed. Install eye shield with
magnifying glass (2) on the left grinding wheel cover, and the
second eye shield (1) on the right grinding wheel cover.
• Use supplied screws, washers and arms to fix eye shields.
• Join transparent plastic plate (a) with metal plate (b) (fig. A).
• Tighten element (b) on the stem and install thus assembled
shield to grinding wheel cover (fig. B).
• Adjust height and angle of eye shields so they match operator
and type of work performed.
10
– 2 pcs (1 piece is magnifying)
– 2 pcs
– 2 pcs
– 1 pce
